Piston Pump (Steering) - Remove
Removal Procedure
Start By:
- Install the body retaining pins. Refer to Disassembly and Assembly , "Body Retaining Pin - Install".
- Release the system hydraulic pressure. Refer to Disassembly and Assembly , "System Hydraulic Pressure - Release".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the oil from the steering tank into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Steering Tank Oil - Change".
- Place a suitable container under the bolts in order to collect fluid. Remove bolts (1) .
Show/hide table
Illustration 1 | g01317123 |
- Remove bolt (2) .
Show/hide table
Illustration 2 | g01317124 |
- Remove bolt (3) .
Show/hide table
Illustration 3 | g01317126 |
- Remove bolts (4) . Position tube assembly (5) out of the way.
Show/hide table
Illustration 4 | g01827001 |
- Disconnect hose assembly (6) .
Show/hide table
Illustration 5 | g01317243 |
- Disconnect hose assembly (7) . Disconnect hose assembly (8) .
Show/hide table
Illustration 6 | g01317130 |
- Disconnect hose assembly (9) .
Show/hide table
Illustration 7 | g01317131 |
- Attach a suitable lifting device to piston pump (10) . The weight of piston pump (10) is approximately 54 kg (120 lb). Remove bolts (11) . Remove piston pump (10) .
Show/hide table
Illustration 8 | g01317136 |
Caterpillar Information System:
414E, 416E, 420E and 430E Backhoe Loaders MID 053 - CID 2652 - FMI 06
AccuGrade® GPS v11 for CD700 Data Card
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System General Information
AccuGrade® CD700 Grade Control System (GPS/ATS/Laser/Cross/Slope/Sonic) v10.8 for Motor Graders Customer Supplied Radio
AccuGrade® CD700 Grade Control System (GPS/ATS/Laser/Cross/Slope/Sonic) v10.8 for Motor Graders Controls
AccuGrade® GPS v11 for CD700 Brightness (Display and Light Bar)
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System Location of Electrical Components
Operation of Product Link{7606} Operation of Product Link{7606}
770 and 772 Off-Highway Truck Hydraulic and Braking System Relief Valve (Hoist Raise, Hoist Lower) - Test and Adjust
CB34 and CC34 Paving Compactors Machine Systems Front Frame and Rear Frame - Connect
777G Off-Highway Truck Machine Systems Wheel Chock (Front and Rear) - Remove and Install
CB34 and CC34 Paving Compactors Machine Systems Front Frame and Rear Frame - Separate
770 and 772 Off-Highway Truck Steering System Piston Pump (Steering)
770 and 772 Off-Highway Truck Hydraulic and Braking System Brake Oil Cooler (Rear)
CP-433E, CS-423E and CS-433E Paving Compactors Hydraulic System Oil Level - Check
2006/10/30 The Fuel Hose is Improved {1261, 1262, 1274}
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Power Train Electronic Control System Service Tools
770 and 772 Off-Highway Truck Hydraulic and Braking System Towing the Machine - Preparation
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System Connector Locations
AccuGrade® GPS v11 for CD700 Design Folder
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Power Train Front Guard - Remove and Install
AccuGrade® CD700 Grade Control System (GPS/ATS/Laser/Cross/Slope/Sonic) v10.8 for Motor Graders Determining Detected Faults (Electronic Service Tool)
AccuGrade® CD700 Grade Control System (GPS/ATS/Laser/Cross/Slope/Sonic) v10.8 for Motor Graders Diagnostic Capabilities
770 and 772 Off-Highway Truck Steering System Solenoid Valve and Manifold (Steering Disable)