Piston Pump (Hydrostatic) - Assemble - Left Side
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-1862 | 钳子 | 1 |
B | 1P-1861 | 挡圈钳 | 1 |
C | 147-8292 | 弹簧压缩器 | 1 |
D | 9U-5720 | 热缩管 | 1 |
E | 129-3883 | 对准螺塞 | 1 |
F | 129-3878 | 测试环 | 1 |
G | 128-2744 | 测量套筒 | 1 |
H | 129-3873 | 测量毂 | 1 |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零件。 棉绒可能会留在零件上,可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 安装环 (70) 和导向环 (69)。
Show/hide table
图 2 g00875604 - 将 O 形密封圈 (68) 安装到盖 (67) 上。
Show/hide table
图 3 g00875602 - 安装盖 (67) 和螺栓 (66)。
Show/hide table
图 4 g00875601 - 安装弹簧挡圈 (63) 和杆 (65)。 安装弹簧 (61)、 (62) 和 (64)。 安装弹簧座 (60)。 安装 O 形密封圈 (58) 和环组件 (59) 。
Show/hide table
图 5 g00875599 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 使用工具 (A) 和适当的压力机安装挡圈 (57)。
Show/hide table
图 6 g00875573 - 将 O 形密封圈 (56) 安装到盖 (55) 上。
Show/hide table
图 7 g00875571 - 安装盖 (55) 和螺母 (54)。
Show/hide table
图 8 g00875570 - 安装弹簧座 (53)。 安装弹簧 (50)、 (51) 和 (52)。 安装弹簧座 (49)。
Show/hide table
图 9 g00875569 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 使用工具 (C) 和适当的压力机安装环组件 (48) 。
Show/hide table
图 10 g00875568 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 使用工具 (A) 和适当的压力机安装挡圈 (47)。
Show/hide table
图 11 g00875567 - 安装伺服阀 (46) 和螺栓 (45) 。
Show/hide table
图 12 g00875539 - 安装轴承 (42)。
Show/hide table
图 13 g00875538 - 安装轴承 (41)、杆 (40) 和滑块 (39)。
Show/hide table
图 14 g00875537 - 安装旋转斜盘组件 (38)。
Show/hide table
图 15 g00875564 - 安装接合销 (43) 和螺塞组件 (44)。
- 对于另一侧,重复步骤 15。
Show/hide table
图 16 g00875224 - 将工具 (D) 安装到轴组件 (36) 上,以便在安装过程中保护轴。 将轴组件 (36) 和 O 形密封圈 (37) 安装到壳体 (4) 上。 安装完成后拆下工具 (D)。
- 将挡圈 (35) 安装到壳体组件 (4) 上。
Show/hide table
图 17 g00875220 - 将密封件 (34) 安装到壳体 (4) 上。
Show/hide table
图 18 g00875204 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将挡圈 (33) 安装到壳体组件 (4) 上。
Show/hide table
图 19 g00875827 - 使用合适的压具将垫圈 (31)、弹簧 (32) 和垫圈 (31) 安装到活塞筒组件 (27) 中。
- 安装挡圈 (30)。
- 使用以下步骤确定旋转总成上的正确垫片厚度。
- 将配流盘 (11) 放置在平板上。 应该将配流盘的平面侧放到平板上。
Show/hide table
图 21 g00875830 Show/hide table图 22 g00875832 - 将工具 (E) 放到配流盘 (11) 的内径上。 斜面侧朝上放置。
- 将活塞筒组件 (27) 安装到工具 (E) 和配流盘 (11) 上。
Show/hide table
图 23 g00875866 - 如图所示,将工具 (F) 安装到活塞筒组件 (27) 的顶部。
Show/hide table
图 24 g00875874 - 确保已经从球窝接头 (26) 上拆下所有弹簧和垫片。 将球窝接头安装到工具 (F) 上。
Show/hide table
图 25 g00875876 - 将固定板 (25) 安装到球窝接头 (26) 上。
Show/hide table
图 26 g00875877 Show/hide table图 27 g00875879 - 用螺栓将工具 (G) 和工具 (H) 拧到一起。 如图所示,将工具 (G) 和 (H) 放到固定板 (25) 的顶部。
Show/hide table
图 28 g00875881 - 使用游标卡尺或类似工具测量步骤 23.i 中的尺寸。
Show/hide table
图 29 g00586062 - 测量从平板的顶部到工具 (G) 的顶部的距离。 将此尺寸记录为尺寸 (X)。 测量从工具 (G) 的顶部到固定板 (25) 的顶部的距离。 将该此尺寸记录为尺寸 (W)。
Show/hide table
表 2 计算 从尺寸 (X) 中减去尺寸 (W) ,即可获得尺寸 (Y) 。 尺寸 (Y) 就是提升高度。 注: 标准机器的提升高度为
100.06 + 0.0 & - 0.2 mm (3.9393 + 0.0 − 0.0079 inch) 。 将这个高度称为尺寸 (Z)。Show/hide table表 3 计算 从尺寸 (Z) 中减去尺寸 (Y) ,即可得到垫片 (29) 的厚度。 由此获得正确的提升高度。
Show/hide table图 20 g00875829 Show/hide table图 30 g00875186 - 将配流盘 (11) 放置在平板上。 应该将配流盘的平面侧放到平板上。
- 安装垫片 (29)。 有关正确尺寸,请参考步骤 23.i。 按照正确顺序安装弹簧组件 (28)。
Show/hide table
图 31 g00875182 - 将球窝接头 (26) 安装到垫片和活塞筒组件 (27) 上。
Show/hide table
图 32 g00875175 - 安装活塞 (24) 和固定板 (25) 。
Show/hide table
图 33 g00875902 - 如图所示,在活塞上缠绕一根尼龙绳。
Show/hide table
图 34 g00875903 - 将旋转组件 (23) 降到泵中。 在安装过程中,使用尼龙绳将组件固定到一起。 拆下尼龙绳。
Show/hide table
图 35 g00875056 Show/hide table图 36 g00875132 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将 O 形密封圈 (21) 安装到补偿器阀 (22) 上。
- 将活塞 (17) 安装到缸盖 (7) 上。
- 将挡圈 (18) 安装到补偿器阀 (22) 上。 将弹簧 (19) 安装到补偿器阀 (22) 上。 将挡圈 (20) 安装到补偿器阀 (22) 上。
- 将补偿器阀 (22) 安装到缸盖 (7) 上。
- 将 O 形密封圈 (16) 安装到测试端口 (15) 上。 将测试端口 (15) 安装到缸盖 (7) 上。
- 将 O 形密封圈 (14) 安装到安全阀 (13) 上。 将安全阀 (13) 安装到缸盖 (7) 中。
- 将 O 形密封圈 (12) 安装到缸盖 (7) 上。
Show/hide table
图 37 g00875055 - 将配流盘 (11) 安装到泵头 (7) 上。
- 将 O 形密封圈 (9) 安装到泵头 (7) 上。
Show/hide table
图 38 g01284387 - 安装连接器 (9) 。
- 将头部 (7) 安装到壳体上。
- 将螺栓 (8) 安装到泵头 (7) 上。
- 安装 O 形密封圈 (9A)。
Show/hide table
图 39 g01284386 - 将法兰 (6) 安装到壳体 (4) 上。
- 将螺栓 (5) 安装到法兰 (6) 上。
Show/hide table
图 40 g01284385 - 安装锥垫圈、 O 形密封圈/电磁阀 (1A) 和螺栓 (1).
- 安装伺服阀 (2B) 和螺栓 (45) 。
- 安装密封垫、盖 (3) 和螺栓 (2)。
Show/hide table
图 1 | g00877519 |
结束:
- 安装活塞泵。 请参阅拆解和组装, "活塞泵(静液压) - 安装"。
Caterpillar Information System:
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Disassemble - Left Side
C175-16 Engine for 795F Series AC Off-Highway Trucks Flywheel Housing - Type 1
Field Service for Positive Pin Retention 2 (PPR 2) {4169, 4170, 4171, 4174, 4175, 4180} Field Service for Positive Pin Retention 2 (PPR 2) {4169, 4170, 4171, 4174, 4175, 4180}
2006/06/26 Correction to Testing and Adjusting , "Torque Converter Stall - Test" {3101}
CB-334E, CB-334E XW, CB-335E, CB34 and CB34 XW and CC34 Vibratory Utility Compactor Systems Radiator and Hydraulic Oil Cooler
C175-16 and C175-20 Generator Set Engines Fuel Lines
New Radios Extend Beyond the Face of the Console{7338} New Radios Extend Beyond the Face of the Console{7338}
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Power Train Modulating Valve (Transmission Clutch)
770, 772, 773E, 773F, 777E and 777F Off-Highway Trucks and 775F Quarry Truck VIMS Truck Payload System Maximum Payload Speed Manager
770, 772, 773E, 773F, 777E and 777F Off-Highway Trucks and 775F Quarry Truck VIMS Truck Payload System Truck Payload - Calibrate
770, 772, 773E, 773F, 777E and 777F Off-Highway Trucks and 775F Quarry Truck VIMS Truck Payload System Truck Payload - Configure
770, 772, 773E, 773F, 777E and 777F Off-Highway Trucks and 775F Quarry Truck VIMS Truck Payload System Payload Management Guidelines
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Disassemble - Right Side
D6K Track-Type Tractor Power Train Piston Pump (Hydrostatic) - Assemble - Right Side
Field Installation of the 258-8355 Backhoe Auxiliary Lines Gp (One-Way Lines Kit) for 416E Backhoes with an Extendable Stick{5057} Field Installation of the 258-8355 Backhoe Auxiliary Lines Gp (One-Way Lines Kit) for 416E Backhoes with an Extendable Stick{5057}
Inspection and Repair Procedure to Replace the Studs for the Rocker Arm Shaft{1102} Inspection and Repair Procedure to Replace the Studs for the Rocker Arm Shaft{1102}
572R Series II Pipelayer Power Train Oil Filter (Power Train)
2006/08/07 The Shaft Assembly for the Drawbar Assembly Has Been Updated {6153}
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System Electronic Control Module (ECM) - Replace
3176C Engines for Caterpillar Built Machines Sensors and Electrical Connectors
14M and 16M Motor Graders Hydraulic and Steering System Blade Lift Cylinder
AQUILATM DrillWizard General Information
AQUILATM DrillWizard Getting Started
AQUILATM DrillWizard Pattern Map