Window Wiper and Wiper Motor (Front) - Remove and Install
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
- Raise the hood.
- Turn the battery disconnect switch to the OFF position.
Show/hide table
Illustration 1 g01174542 - Remove the cable strap and disconnect harness assembly (1).
Show/hide table
Illustration 2 g01174549 - Disconnect hose (2). Remove nut (3). Remove wiper arm (4).
Show/hide table
Illustration 3 g01174561 Show/hide tableIllustration 4 g01174568 - Support wiper motor (9). Remove bolts (5). Remove cap (6), nut (7) and washers (8). Remove wiper motor (9).
Show/hide table
NOTICE |
---|
Do not operate the wiper motor before the wiper arm assembly is installed. A new wiper motor is preset in the parked position. If the wiper motor is operated before installation of the wiper arm assembly, misalignment will occur. This can cause damage to the wiper motor, the wiper arm assembly, and/or the window. Do not manually rotate the wiper arm assembly on the shaft. |
- Position wiper motor (9). Install bolts (5). Install washers (8), nut (7), and cap (6). Tighten nut (7) to a torque of
23 ± 1 N·m (204 ± 9 lb in) . Wait for thirty minutes and tighten nut (7) to a torque of23 ± 1 N·m (204 ± 9 lb in) .Note: Do not wait more than four hours in order to tighten nut (7).
Show/hide tableIllustration 7 g01174549 - Install wiper arm (4). Install nut (3). Connect hose (2).
Show/hide table
Illustration 8 g01174542 - Connect harness assembly (1) and install the cable strap.
- Close the hood.
- Turn the battery disconnect switch to the ON position.
Show/hide table
Illustration 5 | g01174561 |
Show/hide table
Illustration 6 | g01174568 |
Caterpillar Information System:
2005/06/06 A New Valve Cartridge is Now Used on the Counterbalance Valve of the Road Reclaimer/Soil Stabilizer {5420, 5811}
TH210 and TH215 Telehandlers Power Train Hydrostatic Drive Motor - Remove
TH210 and TH215 Telehandlers Machine Systems Boom - Install
793D Off-Highway Truck/Tractor Door Panel (Right) - Remove and Install
793D Off-Highway Truck/Tractor Door Panel (Left) - Remove and Install
C9 Engine for Caterpillar Built Machines Engine Oil Pan - Remove and Install
TH210 and TH215 Telehandlers Machine Systems Boom - Remove
CB-434D, CB-534D, CB-534D Series XW and CB-564D Paving Compactors Traction Control System
2005/06/06 Special Instruction, REHS2624 , "Instructions for Converting Hot Saw to Intermittent Saw " Is Available {5051, 5051, 5057, 6543}
793D Off-Highway Truck/Tractor Air/Hydraulic Cylinder (Rear Brake) - Remove
793D Off-Highway Truck/Tractor Air/Hydraulic Cylinder (Front Brake) - Remove
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
2005/05/30 Special Instruction, REHS2656, "Instructions for Converting Intermittent Saw to Hot Saw" Is Available {5051, 5051, 5057, 6543}
966H Wheel Loader and 972H Wheel Loader Steering System Pilot Valve (Command Control Steering)
TH210 and TH215 Telehandlers Power Train Hydrostatic Drive Motor - Install
C9 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
TH210 and TH215 Telehandlers Power Train Tire and Rim - Remove and Install
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Travel Motor
C9 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
793D Off-Highway Truck/Tractor Start Switch (Key) - Remove and Install
735, 740 and 740 EJECTOR Articulated Trucks Engine Supplement Radiator - Disassemble
2005/06/20 Proper Installation of Jacket Water Heater {1383}
735, 740 and 740 EJECTOR Articulated Trucks Engine Supplement Radiator - Assemble
C18 Engines for Caterpillar Built Machines Diagnostic Codes