Procedure to Install Improved Cab Mounts onSoil Compactors{7301}
- Soil Compactor:
- CP-433E (S/N: ASN1-360)
- CP-533D (S/N: 6AZ1-UP)
- CP-533E (S/N: ASM1-UP)
- CP-563D (S/N: 5LZ1-UP; 9ZW1-UP)
- CP-573E (S/N: ASZ1-201)
- CP-563E (S/N: ASY1-111; BWE1-207; CNT1-741)
- CP-663E (S/N: AFL1-UP; ASF1-206; DAF1-223)
- CS-433E (S/N: ASR1-454)
- CS-533E (S/N: ASL1-UP)
- CP-563D (S/N: 2RZ1-UP; 9MW1-UP)
- CS-563E (S/N: ASA1-673; CNG1-960)
- CS-573D (S/N: 2YZ1-UP; CMK1-UP)
- CS-573E (S/N: CEB1-211; CNN1-223)
- CS-583D (S/N: 2CZ1-UP; 3GZ1-UP)
- CS-583E (S/N: CNX1-332; DAJ1-409)
- CS-663E (S/N: AEF1-UP; ASB1-111; DAG1-424)
- CS-683E (S/N: AGR1-UP; ASG1-310; DAD1-372)
- CP-533D (S/N: 6AZ1-UP)
Introduction
This special instruction provides the necessary information in order to install improved cab mounts on Soil Compactor. The new cab mounts improve the operator comfort on the cab mounted machines.
Disassembly
- Remove the left side panel in order to access the cab mount.
- Remove the nuts, washers, and the bolts that secure the mounts to the frame from both sides of the cab.
- Tilt the cab and secure the cab in the tilted position. The rubber mounts are accessible for removal.
ReferenceSee Disassembly and Assembly, "Cab - Tilt" for the proper tilting procedure.
Show/hide table
 | |
| Illustration 1 | g01162920 |
- With the cab in the tilted position, grind the plate that is used to capture the pivot pins. Additional clearance is needed to install the new cab isolation mounts.
Note: Maintain a minimum of 4 mm (0.2 inch) of material from the edge of the pin holes.
Show/hide table
 | |
| Illustration 2 | g01162924 |
(A) 4 mm (0.2 inch) of material between the edge of the hole and the edge of the plate | |
Installation
Show/hide table
| Required Parts | ||
| Part Number | Description | Qty |
| 7X-2465 (1) | Bolt | 2 |
| 9X-6385 (2) | Bolt | 2 |
| 248-4046 | Mount | 8 |
Show/hide table
| ( 1 ) | Use this bolt to secure the front cab mounts. |
| ( 2 ) | Use this bolt to secure the rear cab mounts. |
- Install rubber mounts into the frame.
- Lower the cab onto the frame.
- Verify that pin hole (B) is in alignment with the frame hole.
Note: Enlarge the holes on the cab frame if the holes are not in alignment.
Show/hide table
 | |
| Illustration 3 | g01163019 |
- Use the existing washers, nuts, and new bolts to secure the cab.
- Torque the nuts to 775 ± 100 N·m (572 ± 74 lb ft).
Caterpillar Information System:
RM-300 Soil Stabilizer Engine Hour Meter
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Power Train Diagnostic Capabilities
1090, 1190, 1190T and 1290T Track Feller Bunchers Maintenance Interval Schedule
C15 and C18 Petroleum Generator Sets After Stopping Engine
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Relief Valve (Vibratory) - Test and Adjust
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Gear Pump Flow (Cooling Fan) - Test
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Gear Pump Flow (Vibratory) - Test
C11 and C15 Engines for Caterpillar Built Machines Engine Shutdown Switch Circuit - Test
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Power Train MID 081 - CID 0590 - FMI 09
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Piston Pump Case Drain Flow (Auxiliary) - Test
3406C Generator Sets Cold Weather Starting
2006/10/30 Using Injector Trim Files {1251, 7620}
RM-300 Soil Stabilizer Equipment Lowering with Engine Stopped
583T Pipelayer Safety Messages
CB-535B Vibratory Compactor Maintenance Interval Schedule
RM-300 Soil Stabilizer Towing the Machine
RM-300 Soil Stabilizer Auxiliary Hydraulic System Filter - Replace
RM-300 Soil Stabilizer Engine Air Precleaner - Clean
RM-300 Soil Stabilizer Engine Oil Level - Check
RM-300 Soil Stabilizer Engine Water Pump - Inspect
2005/05/09 A Pressure Switch for the Hydraulic Lubrication System is Available {7540}
C6.6 Industrial Engine High Pressure Fuel Lines
C7 Engines for Caterpillar Built Machines Piston and Rings
583T Pipelayer Additional Messages