Maintenance Interval Schedule
All safety information, warnings and instructions must be read and understood before you perform any operation or any maintenance procedure. Before each consecutive interval is performed all of the maintenance requirements from the previous interval must also be performed.
Battery - Recycle
Battery or Battery Cable - Inspect/Replace
Cab Air Filter - Clean/Replace
Circuit Breakers - Reset
Fuses - Replace
Hub Oil (Flexxaire Fan) - Add
Hydraulic System Oil Suction Screen - Remove/Clean
Radiator Core - Clean
Track Adjustment - Adjust
Windows - Clean
Cooling System Coolant Level - Check
Fuel Tank Water and Sediment - Drain
Hydraulic System Oil Level (Hood Tilt) - Check
Hydraulic System Oil Level - Check
Seat Belt - Inspect
Tilt Cylinder Bearings - Lubricate
Tilt Linkage Bearings - Lubricate
Track Adjustment - Inspect
Travel Alarm - Test
Undercarriage - Check
Hydraulic System Oil Sample - Obtain
Swing Drive Oil Sample - Obtain
Final Drive Oil Level - Check
Swing Bearing - Lubricate
Swing Drive Oil Level - Check
Swing Gear - Lubricate
Hydraulic System Oil Filter (Case Drain) - Replace
Fuel Tank Cap and Strainer - Clean
Hydraulic System Oil Filter (Pilot) - Replace
Hydraulic System Oil - Change
Hydraulic System Oil Filter (Return) - Replace
Swing Drive Oil - Change
When Required
Air Conditioner/Cab Heater Filter (Recirculation) - Inspect/ReplaceBattery - Recycle
Battery or Battery Cable - Inspect/Replace
Cab Air Filter - Clean/Replace
Circuit Breakers - Reset
Fuses - Replace
Hub Oil (Flexxaire Fan) - Add
Hydraulic System Oil Suction Screen - Remove/Clean
Radiator Core - Clean
Track Adjustment - Adjust
Windows - Clean
Every 10 Service Hours or Daily
Boom Base Pins - LubricateCooling System Coolant Level - Check
Fuel Tank Water and Sediment - Drain
Hydraulic System Oil Level (Hood Tilt) - Check
Hydraulic System Oil Level - Check
Seat Belt - Inspect
Tilt Cylinder Bearings - Lubricate
Tilt Linkage Bearings - Lubricate
Track Adjustment - Inspect
Travel Alarm - Test
Undercarriage - Check
Every 50 Service Hours or Weekly
Boom and Stick Linkage - LubricateInitial 250 Service Hours
Swing Drive Oil - ChangeEvery 250 Service Hours
Battery - CleanHydraulic System Oil Sample - Obtain
Swing Drive Oil Sample - Obtain
Every 250 Service Hours or Monthly
Condenser (Refrigerant) - CleanFinal Drive Oil Level - Check
Swing Bearing - Lubricate
Swing Drive Oil Level - Check
Swing Gear - Lubricate
Every 500 Service Hours
Final Drive Oil Sample - ObtainHydraulic System Oil Filter (Case Drain) - Replace
Every 500 Service Hours or 3 Months
Battery Hold-Down - TightenFuel Tank Cap and Strainer - Clean
Hydraulic System Oil Filter (Pilot) - Replace
Every 1000 Service Hours
Hub Oil Level (Flexxaire Fan) - CheckEvery 1000 Service Hours or 6 Months
Final Drive Oil - ChangeHydraulic System Oil - Change
Hydraulic System Oil Filter (Return) - Replace
Swing Drive Oil - Change
Every 2000 Service Hours or 1 Year
Refrigerant Dryer - ReplaceEvery 3 Years After Date of Installation or Every 5 Years After Date of Manufacture
Seat Belt - ReplaceEvery 6000 Service Hours or 4 Years
Hub Oil (Flexxaire Fan) - ChangeCaterpillar Information System:
C15 and C18 Petroleum Generator Sets After Stopping Engine
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Relief Valve (Vibratory) - Test and Adjust
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Gear Pump Flow (Cooling Fan) - Test
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Gear Pump Flow (Vibratory) - Test
C11 and C15 Engines for Caterpillar Built Machines Engine Shutdown Switch Circuit - Test
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Power Train MID 081 - CID 0590 - FMI 09
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Piston Pump Case Drain Flow (Auxiliary) - Test
3406C Generator Sets Cold Weather Starting
2006/10/30 Using Injector Trim Files {1251, 7620}
2006/10/30 Using Injector Trim Files {1290, 7620}
C11 and C15 Engines for Caterpillar Built Machines User Defined Shutdown Input Circuit - Test
C11 and C15 Engines for Caterpillar Built Machines CAN Data Link Circuit - Test
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Power Train Diagnostic Capabilities
RM-300 Soil Stabilizer Engine Hour Meter
Procedure to Install Improved Cab Mounts onSoil Compactors{7301} Procedure to Install Improved Cab Mounts onSoil Compactors{7301}
RM-300 Soil Stabilizer Equipment Lowering with Engine Stopped
583T Pipelayer Safety Messages
CB-535B Vibratory Compactor Maintenance Interval Schedule
RM-300 Soil Stabilizer Towing the Machine
RM-300 Soil Stabilizer Auxiliary Hydraulic System Filter - Replace
RM-300 Soil Stabilizer Engine Air Precleaner - Clean
RM-300 Soil Stabilizer Engine Oil Level - Check
RM-300 Soil Stabilizer Engine Water Pump - Inspect
2005/05/09 A Pressure Switch for the Hydraulic Lubrication System is Available {7540}