824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System Caterpillar

When the ECM detects an abnormal condition for a certain component or function in the implement electrohydraulic system, a diagnostic code will be activated in order to indicate a problem. When the ECM activates a diagnostic code, refer to the "Troubleshooting" section in this manual for the specific troubleshooting procedure.

Table 1

Diagnostic Codes For The Implement ECM MID 082
CID 0139 Solenoid Valve (Tip Back)
FMI 03	Voltage above normal or shorted high
FMI 05	Current below normal or open circuit
FMI 06	Current above normal or grounded circuit
FMI 13	Out of calibration
CID 0140 Solenoid Valve (Tip Forward)
FMI 03	Voltage above normal or shorted high
FMI 05	Current below normal or open circuit
FMI 06	Current above normal or grounded circuit
FMI 13	Out of calibration
CID 0168 Charging System Voltage
FMI 00	Data valid but above normal range
FMI 01	Data valid but below normal range
CID 0296 Electronic Control Module (Power Train)
FMI 09	Abnormal Update
FMI 12	Bad device or component
CID 0352 Position Sensor (Lift Lever)
FMI 00	Data valid but above normal range
FMI 01	Data valid but below normal range
FMI 03	Voltage above normal or shorted high
FMI 04	Voltage below normal or shorted low
FMI 08	Abnormal frequency, pulse width or period
FMI 13	Out of calibration
CID 0353 Position Sensor (Tilt Lever)
FMI 00	Data valid but above normal range
FMI 01	Data valid but below normal range
FMI 03	Voltage above normal or shorted high
FMI 04	Voltage below normal or shorted low
FMI 08	Abnormal frequency, pulse width or period
FMI 13	Out of calibration
CID 0354 Solenoid Valve (Lift Linkage Raise)
FMI 03	Voltage above normal or shorted high
FMI 05	Current below normal or open circuit
FMI 06	Current above normal or grounded circuit
FMI 13	Out of calibration
CID 0355 Solenoid Valve (Lift Linkage Lower)
FMI 03	Voltage above normal or shorted high
FMI 05	Current below normal or open circuit
FMI 06	Current above normal or grounded circuit
FMI 13	Out of calibration
CID 0358 Solenoid Valve (Pilot Pressure Supply)
FMI 03	Voltage above normal or shorted high
FMI 05	Current below normal or open circuit
FMI 06	Current above normal or grounded circuit
CID 0365 ABP Kickout Set Switch (1)
FMI 04	Voltage below normal or shorted low
CID 0489 Switch (Implement Function Selector)
FMI 03	Voltage above normal or shorted high
FMI 04	Voltage below normal or shorted low
CID 0490 Switch (Implement Lockout)
FMI 03	Voltage above normal or shorted high
FMI 04	Voltage below normal or shorted low
CID 0497 Solenoid Valve (Tilt Right)
FMI 03	Voltage above normal or shorted high
FMI 05	Current below normal or open circuit
FMI 06	Current above normal or grounded circuit
FMI 13	Out of calibration
CID 0498 Solenoid Valve (Tilt Left)
FMI 03	Voltage above normal or shorted high
FMI 05	Current below normal or open circuit
FMI 06	Current above normal or grounded circuit
FMI 13	Out of calibration
CID 0562 Caterpillar Monitoring System
FMI 09	Abnormal Update
FMI 12	Bad device or component
CID 0590 ECM (Engine)
FMI 09	Abnormal Update
FMI 12	Bad device or component
CID 0591 ECM (Implement - Internal Memory)
FMI 12	Bad device or component
CID 0650 Harness Code
FMI 09	Abnormal Update
FMI 11	Failure mode not identifiable
FMI 12	Bad device or component
CID 1393 Driver Enable Line
FMI 04	Voltage below normal or shorted low
CID 1964 Position Sensor (Lift Cylinder) (1)
FMI 00	Data valid but above normal range
FMI 01	Data valid but below normal range
FMI 03	Voltage above normal or shorted high
FMI 04	Voltage below normal or shorted low
FMI 08	Abnormal frequency, pulse width or period
FMI 13	Out of calibration
CID 2119 ABP Enable Switch (1)
FMI 03	Voltage above normal or shorted high
FMI 04	Voltage below normal or shorted low

( 1 )

Can be equipped on 824H and 826H machines only.