Camshaft - Disassemble
Start By:
- Remove the camshaft assembly. Refer to Disassembly and Assembly, "Camshaft - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use a suitable puller to remove the camshaft gear (5) from the camshaft (1).
Note: The camshaft gear should be positioned on a suitable support in order to prevent damage to the governor flyweights during disassembly.
- Remove the spacer (4) and the woodruff key (2) from the camshaft (1).
- Use a suitable puller to remove the front camshaft bearing (3) from the camshaft (1).
Note: Identify the orientation of the camshaft bearing (3) for installation.
- Inspect all of the components for wear or damage. Replace any components that are worn or damaged.
Show/hide table
| |
| Illustration 1 | g01113616 |
|
Typical example | |
Caterpillar Information System:
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Hydraulic Cylinder (Tow Point)
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System Main Control Valve
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Counterbalance Valve (Tow Point)
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System Solenoid Valves (Implement)
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System Pilot Valve (Oil Manifold)
AP-1055D and BG-2455D Asphalt Pavers Auxiliary System Control Valve (Auxiliary)
C11 and C15 Engines for Caterpillar Built Machines Sensors and Electrical Connectors
2004/12/20 A New Two-Piece Seal Is Used in Various Metering Pumps (Steering) and in the New 257-8471 Seal Kit {4312}
Installing the 218-6739 High Flow Conversion Kit {5057, 5059, 5073, 5264, 5705} Installing the 218-6739 High Flow Conversion Kit {5057, 5059, 5073, 5264, 5705}
2006/02/20 Magnetic Cover for the Turbocharger Oil Supply Line {1052, 1307}
2005/01/10 Procedure to Identify which COM PORT the USB Device Is Occupying and the Procedure to Change the Default COM PORT Setting {7606}
2006/02/20 Magnetic Cover for the Turbocharger Oil Supply Line {1052, 1307}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Assemble
988H and 988K Wheel Loaders Power Train Transmission Oil Pump - Disassemble
988H and 988K Wheel Loaders Power Train Transmission Oil Pump - Assemble
H35E S, H45E S, H55E S and H65E S Hydraulic Hammers Shipping
BD118 and BD121 Side Discharge Bucket Storage
C9 Engines for Caterpillar Built Machines Electronic Control System Components
C9 Engines for Caterpillar Built Machines Basic Engine
12M, 140M and 160M Motor Graders Braking and Hydraulic Fan System Brake and Hydraulic Fan System
834H Wheel Dozer and 836H Landfill Compactor Steering System Relief Valve (Pump Backup) - Test and Adjust
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Flash Programming
Asphalt Pavers Burner Electronic Control System Glow Plug
793D Off-Highway Truck Additional Messages