Piston Motor (Propel) - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
B     | 1P-1859     | 挡圈钳     | 1     |
C     | 8H-0663     | 轴承拉拔器总成     | 1     |
开始:
- 拆下推进马达。 请参阅拆解和组装, "活塞马达(推进)- 拆卸"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 将螺栓 (1) 和盖 (2) 从壳体 (3) 上拆下。
Show/hide table
图 1 | g01073562 |
- 从壳体 (3) 上卸下 O 形密封圈 (4) 。
- 使用适当的压具和工具 (A) 将唇形密封 (5) 从盖 (2) 上拆下。
Show/hide table
图 2 | g01073572 |
- 将 O 形密封圈 (6) 从盖 (2) 上拆下。
- 将轴 (7) 从壳体 (3) 上拆下。
Show/hide table
图 3 | g01073573 |
- 使用工具 (B) 将挡圈 (8) 从轴 (7) 上拆下。
Show/hide table
图 4 | g01073579 |
- 使用工具 (C) 和适当的压具将轴承 (9) 从轴 (7) 上拆下。
- 拆下螺栓 (17) 和支架 (16) 。 松开螺母 (15) ,然后将转速传感器 (14) 从壳体上拆下。
Show/hide table
图 5 | g01073582 |
- 安装将盖 (11) 固定到壳体的四个螺栓 (10) 和螺栓 (12) 。 松开两个螺栓 (13) 。 此时不要拆下两个螺栓 (13) 。
- 将 O 形密封圈 (18) 从转速传感器 (14) 上拆下。
Show/hide table
图 6 | g01073724 |
- 放置推进马达,如图所示。 拆下两个螺栓 (13) ,然后将壳体 (3) 从盖 (11) 上拆下。
Show/hide table
图 7 | g01073583 |
- 将板 (19) 从壳体 (3) 上拆下。
Show/hide table
图 8 | g01073584 |
- 将密封垫 (20) 从盖 (11) 上拆下。
Show/hide table
图 9 | g01073587 |
- 将管 (21) 从盖 (11) 上拆下。
Show/hide table
图 10 | g01073588 |
- 将导向器 (22) 和活塞从管 (21) 上拆下。
Show/hide table
图 11 | g01073589 |
- 将活塞 (23) 从导向器 (22) 上拆下。
Show/hide table
图 12 | g01073590 |
- 将护圈 (24) 从管 (21) 上拆下。
Show/hide table
图 13 | g01073591 |
- 将垫片 (25) 从管 (21) 上拆下。
Show/hide table
图 14 | g01073592 |
- 将缸体 (26) 从盖 (11) 上拆下。
Show/hide table
图 15 | g01073594 |
- 将缸体 (26) 放置到适当的压具中。 安装一个与垫圈 (27) 尺寸相同的适当传动板。 使用压具在垫圈 (27) 上稍微施加压力。 拆下挡圈 (28) ,然后缓慢释放弹簧压力。
Show/hide table
图 16 | g01073983 |
Show/hide table
图 17 | g01073984 |
Show/hide table
拆卸固定环和弹簧时,可能会造成伤害。 拆卸固定环时,将释放弹簧力。 拆卸固定环时,做好固定油缸组件的准备。 |
- 将垫圈 (27) 、弹簧 (30) 和垫圈 (29) 从缸体 (26) 上拆下。
- 将板 (31) 和销 (32) 从盖 (11) 上拆下。
Show/hide table
图 18 | g01074006 |
- 将轴承 (33) 从盖 (11) 上拆下。
Show/hide table
图 19 | g01074007 |
- 将螺塞 (34) 、弹簧 (36) 和阀 (37) 从适配器 (38) 上拆下。 从螺塞 (34) 拆下 O 形密封圈 (35) 。
Show/hide table
图 20 | g01074017 |
Show/hide table
拆卸固定环和弹簧时,可能会造成伤害。 拆卸固定环时,将释放弹簧力。 拆卸固定环时,做好固定油缸组件的准备。 |
- 将适配器 (38) 从盖 (11) 上拆下。 从适配器 (38) 上卸下 O 形密封圈 (39) 。
- 将螺塞 (40) 和 (41) 从盖 (11) 上拆下。 将 O 形密封圈从螺塞 (40) 和 (41) 上拆下。
- 将螺塞 (45) 和座椅 (43) 从盖 (11) 的两侧拆下。 将 O 形密封圈 (44) 从螺塞 (45) 上拆下。
- 将滑阀 (42) 从盖 (11) 上拆下。
Caterpillar Information System:
988H Wheel Loader, 834H Wheel Dozer and 836H Landfill Compactor Machine Systems Muffler
12M Motor Grader Transmission and Differential Oil Sample - Obtain
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Engine Oil Level - Check
247B, 257B, 267B, 277B and 287B Multi Terrain Loaders Reference Material
416E Backhoe Loader Additional Messages
3054 Engine for Caterpillar Built Machines Front Cover - Remove
AP-800D and BG-230D Asphalt Pavers Engine Starting
C27 and C32 Engines for Caterpillar Built Machines Connecting Rod
770 and 772 Off-Highway Truck Oil Filter (Brake, Hydraulic Fan) - Replace
16H Motor Grader Machine Systems Ripper Lift Cylinder - Remove and Install
CB-214E, CB-224E and CB-225E Vibratory Compactors Vibratory System Electrical Schematic
PF-300C and PS-300C Pneumatic Compactors Machine System Spray Nozzle - Adjust
AP655F and AP655F L Asphalt Paver Machine Systems Piston Motor (Propel) - Assemble
770 and 772 Off-Highway Truck Oil Filter (Power Train) - Replace
R1600G Load Haul Dump Machine Systems Pilot Valve (STIC Steering) - Disassemble
R1600G Load Haul Dump Machine Systems Pilot Valve (STIC Steering) - Assemble
R1300G Load Haul Dump Remote Control System Machine Preparation for Troubleshooting
R2900G Load Haul Dump Machine Systems Main Control Valve - Disassemble
R2900G Load Haul Dump Machine Systems Bucket Control Safety Pins - Remove and Install
3406C Engines for Caterpillar Built Machines Electric Starting Motor
PF-300C and PS-300C Pneumatic Compactors Machine System Relief Valve (Suspension) - Test and Adjust
3176C and 3196 Engines for Caterpillar Built Machines Electric Starting Motor
12M Motor Grader Axle Oscillation Bearings - Lubricate
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Operation