Piston Motor (Propel) - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
B     | 1P-1859     | 挡圈钳     | 1     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洁液体彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零件。 棉绒可能会留在零件上,可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 将滑阀 (42) 安装到盖 (11) 中。
Show/hide table
图 1 | g01074017 |
Show/hide table
拆卸固定环和弹簧时,可能会造成伤害。 拆卸固定环时,将释放弹簧力。 拆卸固定环时,做好固定油缸组件的准备。 |
- 将 O 形密封圈 (44) 安装到螺塞 (45) 上。 将座椅 (43) 和螺塞 (45) 安装到盖 (11) 的两侧。
- 将 O 形密封圈安装到螺塞 (40) 和 (41) 上。 将螺塞 (40) 和 (41) 安装到盖 (11) 中。
- 将 O 形密封圈 (39) 安装在适配器 (38) 上。 将适配器 (38) 安装在盖 (11) 中。
- 将 O 形密封圈 (35) 安装在螺塞 (34) 上。 将阀 (37) 、弹簧 (36) 和螺塞 (34) 安装在适配器 (38) 中。
- 使用工具 (A) 和适当的压具将轴承 (33) 安装在盖 (11) 中。
Show/hide table
图 2 | g01074007 |
- 将销 (32) 和板 (31) 安装在盖 (11) 中。
Show/hide table
图 3 | g01074006 |
- 将垫圈 (29) 、弹簧 (30) 和垫圈 (27) 安装在缸体 (26) 中。
Show/hide table
图 4 | g01073984 |
Show/hide table
图 5 | g01073983 |
Show/hide table
拆卸固定环和弹簧时,可能会造成伤害。 拆卸固定环时,将释放弹簧力。 拆卸固定环时,做好固定油缸组件的准备。 |
- 将缸体 (26) 放置到适当的压具中。 将适当的传动板安装在垫圈 (27) 上,压缩弹簧 (30) 直到可以安装挡圈 (28) 为止。
- 将缸体 (26) 放置在板和盖 (11) 上。
Show/hide table
图 6 | g01073594 |
- 将管 (21) 放置在盖 (11) 上。
Show/hide table
图 7 | g01074233 |
- 将垫片 (25) 安装在管 (21) 上。
Show/hide table
图 8 | g01074234 |
- 将护圈 (24) 安装在管 (21) 上。
Show/hide table
图 9 | g01074236 |
- 将活塞 (23) 安装在导向器 (22) 中。
Show/hide table
图 10 | g01073590 |
- 将活塞 (23) 安装在缸体 (26) 中。
Show/hide table
图 11 | g01074237 |
- 将板 (19) 放置在管 (21) 上。
Show/hide table
图 12 | g01074238 |
- 将密封垫 (20) 安装在盖 (11) 上。
Show/hide table
图 13 | g01074246 |
- 将壳体 (3) 放置在盖 (11) 上,然后安装两个螺栓 (13) 。
Show/hide table
图 14 | g01073583 |
- 加热轴承 (9) 。 将轴承 (9) 安装在轴 (7) 上。 使用工具 (B) 将挡圈 (8) 安装在轴 (7) 上。
Show/hide table
图 15 | g01073579 |
- 将轴 (7) 安装在壳体 (3) 中。
Show/hide table
图 16 | g01074306 |
- 使用工具 (A) 和适当的压具将唇形密封 (5) 安装在盖 (2) 中。
Show/hide table
图 17 | g01073572 |
- 将 O 形密封圈 (6) 安装在盖 (2) 上。
- 安装盖 (2) 和螺栓 (1) 。
Show/hide table
图 18 | g01074308 |
- 将 O 形密封圈 (4) 安装在壳体 (3) 上。
- 将 O 形密封圈 (18) 安装在转速传感器 (14) 上。
Show/hide table
图 19 | g01073724 |
- 安装将盖 (11) 固定到壳体 (3) 的四个螺栓 (10) 和螺栓 (12) 。
Show/hide table
图 20 | g01074327 |
Show/hide table
图 21 | g02546689 |
- 将转速传感器 (14) 拧入壳体 (3) ,直到转速传感器 (14) 的端部与齿轮 (18) 接触。
- 将转速传感器 (14) 拧松一圈 (A) 的八分之一。
- 旋转转速传感器 (14) ,以便可以安装支架 (16) 。 确保转速传感器不与齿轮 (18) 接触。 此时不要安装支架。
注: 支架 (16) 确保转速传感器以适当的相角安装。
- 固定转速传感器 (14) ,然后将锁紧螺母 (15) 拧紧至 13 N·m (9 lb ft) 的扭矩。
- 安装支架 (16) 和螺栓 (17) 。
End By: 安装推进马达。 请参阅 拆解和组装, "活塞马达(推进)- 安装"。
Caterpillar Information System:
AP655F and AP655F L Asphalt Paver Machine Systems Piston Motor (Propel) - Disassemble
988H Wheel Loader, 834H Wheel Dozer and 836H Landfill Compactor Machine Systems Muffler
12M Motor Grader Transmission and Differential Oil Sample - Obtain
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Engine Oil Level - Check
247B, 257B, 267B, 277B and 287B Multi Terrain Loaders Reference Material
416E Backhoe Loader Additional Messages
3054 Engine for Caterpillar Built Machines Front Cover - Remove
AP-800D and BG-230D Asphalt Pavers Engine Starting
C27 and C32 Engines for Caterpillar Built Machines Connecting Rod
770 and 772 Off-Highway Truck Oil Filter (Brake, Hydraulic Fan) - Replace
16H Motor Grader Machine Systems Ripper Lift Cylinder - Remove and Install
CB-214E, CB-224E and CB-225E Vibratory Compactors Vibratory System Electrical Schematic
770 and 772 Off-Highway Truck Oil Filter (Power Train) - Replace
R1600G Load Haul Dump Machine Systems Pilot Valve (STIC Steering) - Disassemble
R1600G Load Haul Dump Machine Systems Pilot Valve (STIC Steering) - Assemble
R1300G Load Haul Dump Remote Control System Machine Preparation for Troubleshooting
R2900G Load Haul Dump Machine Systems Main Control Valve - Disassemble
R2900G Load Haul Dump Machine Systems Bucket Control Safety Pins - Remove and Install
3406C Engines for Caterpillar Built Machines Electric Starting Motor
PF-300C and PS-300C Pneumatic Compactors Machine System Relief Valve (Suspension) - Test and Adjust
3176C and 3196 Engines for Caterpillar Built Machines Electric Starting Motor
12M Motor Grader Axle Oscillation Bearings - Lubricate
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Operation
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Specifications