Solenoid Valve (Compressor Motor) - Remove and Install
Removal Procedure
Start By:
- Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
- Raise the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
- Disconnect harness assembly (1). Remove nut (2) and remove coil assembly (3) .
Show/hide table
 | |
| Illustration 1 | g01055162 |
- Remove valve (4) .
Show/hide table
 | |
| Illustration 2 | g01055180 |
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install valve (4) .
Show/hide table
| | |
| Illustration 3 | g01055180 |
- Install coil assembly (3). Install nut (2). Connect harness assembly (1) .
Show/hide table
| | |
| Illustration 4 | g01055162 |
End By: Lower the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Caterpillar Information System:
160M Motor Grader Specifications
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0603 - FMI 04
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0603 - FMI 03
2004/05/03 Identifying the Throttle Cable {1265}
2004/05/03 Follow the Recommended Procedure for Clearing Errors for the Transmission Output Speed Sensor {3175}
2004/05/10 The New Level Sensor Has Improved Service Life in Extended Life Coolant {7422}
Conversion of the 157-2812 Air Compressor Gp to the 113-8193 Air Compressor Gp for Certain Off-Highway Truck Applications{1803} Conversion of the 157-2812 Air Compressor Gp to the 113-8193 Air Compressor Gp for Certain Off-Highway Truck Applications{1803}
AS2251 and AS2301 Asphalt Screed Screed Heat Control
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Work Tool Operation
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Tilt Cylinder - Remove and Install
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Lift Cylinder - Remove and Install
770 and 772 Off-Highway Truck Engine Oil Sample - Obtain
10-20B and 8-16B EXTEND A MAT SCREEDS Additional Messages
267B, 277B and 287B Multi Terrain Loaders Machine Systems Refrigerant Compressor and Support Housing - Remove and Install
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1956 - FMI 03
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1956 - FMI 04
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1956 - FMI 08
CB-214E, CB-224E and CB-225E Vibratory Compactors Propel System Piston Motors (Drum Propel and Wheel Propel)
267B, 277B and 287B Multi Terrain Loaders Machine Systems Refrigerant Condenser and Mounting - Remove and Install
2004/04/19 A New Valve Cover Seal and New Valve Cover Fasteners are Now Available {1107}
267B, 277B and 287B Multi Terrain Loaders Machine Systems Gear Motor - Remove
Bench Test Procedure for Hydraulic Piston Pumps {3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps {3203, 5070}
Bench Test Procedure for Hydraulic Piston Pumps {3203} Bench Test Procedure for Hydraulic Piston Pumps {3203}
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}