Parking Brake - Remove and Install
拆卸步骤
开始:
- 把驱动轴取下。 请参考拆解和装配, "驱动轴 - 拆卸和安装"。
- 松开停车制动器。 参见 操作和保养手册, "操作员控制装置"。
- 拆下螺栓 (1) 和护圈 (2) 。
Show/hide table
 | |
| 图 1 | g00663592 |
- 拆下制动鼓 (3) 。
Show/hide table
 | |
| 图 2 | g00663600 |
- 卸下螺栓 (5) 。
注: 当您拆下制动器组件 (6) 时，连杆组件 (4) 将掉落。
Show/hide table
 | |
| 图 3 | g00891200 |
- 拆下制动器组件 (6) 。
- 拆下弹簧 (6) 后分离制动器组件 (7) 。
Show/hide table
 | |
| 图 4 | g00891201 |
Show/hide table
 |
弹簧压缩零件如果安装不当，会伤害人体。 为避免伤害，遵照出版的装配程序，并穿上保护装备。 |
安装步骤
- 组装停车制动器 (7) 后安装弹簧 (6) 。
Show/hide table
| | |
| 图 5 | g00891201 |
Show/hide table
|
弹簧压缩零件如果安装不当，会伤害人体。 为避免伤害，遵照出版的装配程序，并穿上保护装备。 |
- 安装连杆组件 (4) 和制动器组件 (6) 。
Show/hide table
| | |
| 图 6 | g00891200 |
- 安装螺栓 (5) 。 将螺栓 (5) 上紧到 120 ± 20 N·m (89 ± 15 lb ft) 的扭矩。
- 安装制动鼓 (3) 。
Show/hide table
| | |
| 图 7 | g00663600 |
- 安装座圈 (2) 和螺栓 (1) 。 将螺栓 (1) 上紧到 120 ± 20 N·m (89 ± 15 lb ft) 的扭矩。
Show/hide table
| | |
| 图 8 | g00663592 |
- 调整停车制动器。 请参阅测试和调整, "停车制动器控制拉线 - 调整"。
End By: 安装驱动轴。 请参考 拆解和装配, "驱动轴 - 拆卸和安装"。
Caterpillar Information System:
Product Link - PL102C System Overview
PS-150C Pneumatic Compactor Propel System Air Inflation Group
PS-150C Pneumatic Compactor Propel System Wheel and Tire
2004/04/19 Correction to Operation and Maintenance Manual , "Engine Shutdown Switch" {7418}
2004/03/29 Correction to Operation and Maintenance Manual , "Battery Disconnect Switch" {1411}
R1700G Load Haul Dump Engine Shutdown Switch
R2900G Load Haul Dump Power Train Torque Converter - Assemble
R1700G Load Haul Dump Battery Disconnect Switch
AP500F Asphalt Paver Machine Systems Push Roller - Assemble
AP500F Asphalt Paver Machine Systems Push Roller - Disassemble
R2900G Load Haul Dump 3406E AND C15 Engine Supplement Engine Mounting (Rear)
Bench Test Procedure for a 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 930H Wheel Loader and IT28G Integrated Toolcarrier Transmission{3030, 3073, 3139} Bench Test Procedure for a 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 930H Wheel Loader and IT28G Integrated Toolcarrier Transmission{3030, 3073, 3139}
PS-150C Pneumatic Compactor Propel System Hand Pump (Manual Brake Release)
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Warning "Engine Oil Pressure Is Low" Is Displayed - Troubleshoot
2004/03/22 Corrections to Special Instruction, REHS1738, "Installing the "B Series" Cab Door Kits" {7308}
2004/03/22 Special Instruction, REHS1837 , "Bench Test Procedure for Bosch Rexroth A6VM HD Motors" Is Now Available {5058}
216B, 216B2, 226B, 226B2, 232B, 232B2, 242B and 242B2 Skid Steer Loaders Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
3406E, C-10, C-12, C-15, C-16 Truck Engines Product Storage
216B, 226B, 232B and 242B Skid Steer Loaders Machine Systems Hydrostatic System - Test and Adjust
14H and 16H Motor Graders Hydraulic and Steering System Hydraulic and Steering System
2006/01/02 Relocation of the Fuel Transfer Pump is Recommended for Certain Applications. {1256}
PS-150C Pneumatic Compactor Machine System Hydraulic Oil Filter
C15 and C18 Generator Set Engines Electronic Unit Injector - Remove
247B2 and 257B2 Multi Terrain Loaders Machine Systems Hydrostatic System - Flush and Fill