Correction to Operation and Maintenance Manual , "Engine Shutdown Switch" {7418}
- Load Haul Dump:
- R1700G (S/N: 8XZ299-UP)
The following information is an addition to the operation section of the Operation and Maintenance Manual. The engine shutdown switch is in a new position. The new position for the engine shutdown switch is effective with S/N:8XZ299-UP.
Engine Shutdown Switch
Show/hide table
 | |
| Illustration 1 | g01059487 |
Show/hide table
 | |
| Illustration 2 | g01059488 |
The engine shutdown switch (1) is located on the right rear side of the machine.
Show/hide table
| Engine Shutdown Switch (1) - Use engine shutdown switch (1) in order to stop the engine from the ground level. In order to use engine shutdown switch (1), push the engine shutdown switch knob in to the OFF position. This will stop the engine. After the engine stops, turn the knob clockwise. This will reset the engine shutdown switch to the ON position. |
During normal operation, use the engine start switch to stop the engine.
Note: The engine shutdown switch does not shut off the electrical system of the machine.
Caterpillar Information System:
2004/03/29 Correction to Operation and Maintenance Manual , "Battery Disconnect Switch" {1411}
R1700G Load Haul Dump Engine Shutdown Switch
R2900G Load Haul Dump Power Train Torque Converter - Assemble
R1700G Load Haul Dump Battery Disconnect Switch
AP500F Asphalt Paver Machine Systems Push Roller - Assemble
AP500F Asphalt Paver Machine Systems Push Roller - Disassemble
R2900G Load Haul Dump 3406E AND C15 Engine Supplement Engine Mounting (Rear)
Bench Test Procedure for a 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 930H Wheel Loader and IT28G Integrated Toolcarrier Transmission{3030, 3073, 3139} Bench Test Procedure for a 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 930H Wheel Loader and IT28G Integrated Toolcarrier Transmission{3030, 3073, 3139}
267B, 277B and 287B Multi Terrain Loaders Power Train Track Drive - Disassemble
R2900G Load Haul Dump 3406E AND C15 Engine Supplement Engine Mounting (Front)
PS-150C Pneumatic Compactor Propel System Front Axle
PS-150C Paving Compactor Air Compressor Air Filter - Replace
PS-150C Pneumatic Compactor Propel System Wheel and Tire
PS-150C Pneumatic Compactor Propel System Air Inflation Group
Product Link - PL102C System Overview
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Power Train Parking Brake - Remove and Install
PS-150C Pneumatic Compactor Propel System Hand Pump (Manual Brake Release)
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Warning "Engine Oil Pressure Is Low" Is Displayed - Troubleshoot
2004/03/22 Corrections to Special Instruction, REHS1738, "Installing the "B Series" Cab Door Kits" {7308}
2004/03/22 Special Instruction, REHS1837 , "Bench Test Procedure for Bosch Rexroth A6VM HD Motors" Is Now Available {5058}
216B, 216B2, 226B, 226B2, 232B, 232B2, 242B and 242B2 Skid Steer Loaders Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
3406E, C-10, C-12, C-15, C-16 Truck Engines Product Storage
216B, 226B, 232B and 242B Skid Steer Loaders Machine Systems Hydrostatic System - Test and Adjust
14H and 16H Motor Graders Hydraulic and Steering System Hydraulic and Steering System