1979/03/14 Caterpillar


New Fuel Injection Nozzles Are Used In 3208 Engines

Usage:




3208 Engines;
Industrial (90N37285-Up);
Marine (75V4002-Up);
Vehicular (79V5380-Up) and Truck (32Y1-Up)

SUPPLEMENT: 05/09/79

ENGINE NEWS, MARCH 14, 1979, PAGE 2.

In the article "New Fuel Injection Nozzles Are Used In 3208 Engines", the 75V4002-up Serial Number shown for marine engines is wrong. Change 75V4002-up to read 75V4113-up.

--------------- END SUPPLEMENT ---------------

Description of Change: A new fuel injection nozzle is used on 3208 Engines starting with the serial numbers shown above. The new injection nozzle has a smaller "SAC" volume than the former injection nozzle. "SAC" volume is the remainder of fuel in the tip of the injector nozzle after injection. This gives a reduction in the amount of fuel that will get into the cylinder after each injection. The new fuel injection nozzles give a reduction in the amount of hydro-carbon emissions.

Adaptable To: The new 9N3979 Injection Nozzle Assembly is used in the engines shown above, including truck engines that are equipped with exhaust gas recirculation (EGR) systems.

This new nozzle must not be used in 3208 Engines that have serial numbers earlier than those shown. The 9N3299 and 9L6969 Fuel Injection Nozzles are still available for parts service of earlier 3208 Engines.

Caterpillar Information System:

1979/03/14 New Piston And Connecting Rod Are Tapered In Area Of Piston Pin
1979/03/14 New Oil Filter And Filter Base Assemblies
1979/03/07 New Exhaust Pipe Connector Makes A Tighter Seal Between Pipe And Manifold
1979/03/07 Retroreflective Tape Makes Phototach Kit Easier To Read
1979/03/07 Window Cover Kit Now Available For ENM Service Meters
1979/03/07 Use SIRS To Keep Service Literature Current
1979/03/07 Check Valve Must Be Adjusted Correctly To Let Fuel Flow Through The Return Line And Back To The Tank
1979/03/07 New Fuel Injection Lines Groups Use A Different Fuel Injection Nozzle Assembly
1979/03/07 Engine Valve Springs Are Now Made Of Carbon Steel Alloy
1979/03/07 New Manifold Assembly Gives More Room For The Lifting Eye
1979/03/07 New Exhaust Valve And Valve Guide
1979/03/07 Engine Mounted Exhaust Brake Systems Can Be Used To Extend Service Brake Life
1979/03/14 New Engine Cylinder Block Used
1979/03/14 Improvements Made To Fuel Injection Pump And Governor Group
1979/03/14 8L4525 Flange Is Available Again For Parts Service Of 3192 Marine Transmissions
1979/03/14 Main Bearings Now Have Larger Diameter Oil Hole For Better Lubrication Of Main And Rod Bearings
1979/03/14 Maintenance Procedures For Extended FPTO Life On 3408 And 3412 Marine Engines
1979/03/14 Larger Diameter Washer Is Used To Hold Air Transfer Pipe In Aftercooler Flange
1979/03/14 List Of Service Publications
1979/03/14 Revision To Guideline For Reusable Parts Is Available
1979/03/14 Information About The Use Of Earlier Cylinder Heads And Liners With Spacer Plate Cylinder Blocks; List Of Earlier Articles
1979/03/14 Replacement Bushing Available For Cast Iron Rocker Arms Only
1979/04/04 New Fabricated Tools Available For Service Work On 7211 And 7221 Marine Transmissions
1979/04/04 New Oil Jet Tube In Cylinder Block Gives More Clearance For Pistons And Connecting Rods
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.