814K, 816K, 826K 836K Landfill Compactors, 815K, 825K, Soil Compactors, 824K, 834K, 844K, 854K Wheel Dozers and 986K, 988K, 990K, 992K,994K Wheel Loaders Information Display Caterpillar

Flashing the Secondary Display

Equipment Required

• VIMS cable: ( 305-5528 Wiring Harness)

• Current version of Cat^® Electronic Technician (Cat ET) Service Tool

• PC with an Ethernet Port

Note: The display can only be flashed with a direct Ethernet connection. To flash, connect an Ethernet cable to the RJ45 port on the CA3 adapter harness. Connect the remaining end of the Ethernet cable to the LAN connection on the computer.

Cat^® Electronic Technician (Cat ET) Service Tool Setup Instructions

Note: If using the Laptop Ethernet Port, then turn OFF (Do NOT minimize) all other applications prior to starting Cat ET. Optionally use a USB to Ethernet Adapter.

1. Connect to WINFLASH in Cat ET.

2. Under the "Utilities" menu, select "Preferences".

3. Select "Modify" to change connection settings in Cat ET.
   Show/hide table

   Illustration 1	g03485478

4. Under the "Communications" tab, change the connection type to "Ethernet Direct Connection" (Illustration 2).
   Show/hide table

   Illustration 2	g03485516

5. Select the "Network Adapter Connection" that supports the "Ethernet Direct Connection" (Illustration 3). If using the optional USB to Ethernet Adapter, be sure to select this device from the drop-down menu.
   Show/hide table

   Illustration 3	g03485581

6. Cat ET may attempt to reconnect based on the change of Communication Protocol. Click "Yes" (Illustration 4).
   Show/hide table

   Illustration 4	g03485596

7. When Cat ET reconnects, it will attempt to detect an ECM using "IP Data Link" (Illustration 5).
   Show/hide table

   Illustration 5	g03485758

8. Select the Flash File when the ECM is detected. Initiate the Flash process (Illustration 6).

   Note: Wait until Cat ET shows 100% completed, even if the display looks like it is working during Flashing.

   Show/hide table

   Illustration 6	g03485796

9. Click "OK" when Cat ET provides a warning that the Operating System will be changed.
   Show/hide table

   Illustration 7	g03485900

10. During the Flashing process, the screens shown in Illustration 8 through 10 will be displayed.

    Note: Wait until the Flash Process has completed.

    Show/hide table

    Illustration 8	g03487493

    Show/hide table

    Illustration 9	g03487401

    Show/hide table

    Illustration 10	g06014093

    Note: Wait until "Flash Completed Successfully" displays. Click "Cat ET".

    Show/hide table

    Illustration 11	g03494458

11. After Flashing, change Communication settings back to "Comm Adapter 3" (or "Comm Adapter 2").
    Show/hide table

    Illustration 12	g03494483

12. Connect to Cat ET.

13. Go to Display "Configurations".

14. Verify that the Product ID matches the Machine Product ID. If the Product ID does not match, change the cycle power to the machine so that the Display can re-request the Product ID from the Machine ECM. (Illustration 13).

    Note: Illustration 13 is a sample screenshot for D9T REX00301. New Flashing information will be different.

Illustration 13	g03494716

Flashing Example

The following is an example of approximate numbers and timing recorded during a Flash with no bus traffic:

• Cat ET shows 18% at 16 seconds.

• Cat ET shows 45% at approximately 26 seconds.

• Reboot at 38 seconds.

• Eboot erasing at 48 seconds.

• Eboot loading done at 1:04.

• Erasing NOR at 1:05.

• Erasing NOR OS space ends at 2:37.

• Programming OS starts at 2:38.

• Programming OS ends at 6:14.

• Display has rebooted, but is older cab file at 6:30.

• Cat ET shows 50% at 6:38.

• Cat ET shows 90% at 6:45.

• Reboots.

• Cab file extraction at 7:07.

• Reboots and shows new cab file at 8:09.

• Cat ET shows 100% at 8:19.