Cylinder Block Cover - Remove and Install
Start By:
- Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Loosen hose clamp (1) and disconnect hose assembly (2).
- Disconnect tube assembly (3).
- Disconnect hose assembly (7).
- Disconnect harness assembly (6).
- Remove bolts (4). Remove cylinder block cover (5). Remove the O-ring seals and the gasket from the cylinder block.
Show/hide table
| |
| Illustration 1 | g01435498 |
- Install the O-ring seals and the gasket on the cylinder block. Position cylinder block cover (5).
- Install bolts (4). Tighten bolts (4) by using the following procedure:
- Tighten the bolts in a numerical sequence.
- Tighten the bolts again in a numerical sequence.
- Connect harness assembly (6).
- Connect hose assembly (7).
- Connect tube assembly (3).
- Connect hose assembly (2) and tighten hose clamp (1).
Show/hide table
|
| |
| Illustration 2 | g01435498 |
Show/hide table
| |
| Illustration 3 | g01435572 |
Note: Check the condition of the O-ring seals and the gasket. Replace the O-ring seals and the gasket, if necessary.
End By:
- Install the electronic control module. Refer to Disassembly and Assembly, " Electronic Control Module - Remove and Install".
Caterpillar Information System:
G3600 Engines Sensor Signal (PWM) - Test
C9 Petroleum Engines Crankcase Breather - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Install
C4.4 Generator Set Engines Injector Solenoid Circuit - Test
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Assemble
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Disassemble
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Install
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Remove
C9 Petroleum Engines Housing (Front) - Install
C15 and C18 Petroleum Generator Sets Speed Sensor - Clean/Inspect
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission and Torque Converter - Connect
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission and Torque Converter - Separate
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Fasteners
G3600 Engines Fuel Control - Test
320D and 323D Excavators Hydraulic System Swing Drive
C9 Petroleum Engines Rocker Arm and Shaft - Install
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224} Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Troubleshooting Diagnostic Codes
2007/12/03 Improved Wiring for the Speed Control for the Electronic Governor {1408, 1417}
C9 Petroleum Engines Cylinder Head - Remove
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Display of Voltage or Current or Power Is Inaccurate
G3600 Engines Prelubrication - Test
Caterpillar Machine Fluids Recommendations Distillate Diesel Fuel
C9 Petroleum Engines Cylinder Head - Install