Clean Gas Induction Valve - Assemble
Note: This component is being disassembled and displayed for CLEANING PURPOSES ONLY. Many internal parts are not available for this component. Care must be taken during disassembly and assembly in order to prevent damage to unavailable parts.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Check O-ring seal (13) for wear or for damage. If necessary, replace O-ring seal (13).
Show/hide table
Illustration 2 g01265787 - Install housing (11). Install bolts (10). If wiper (12) is worn or damaged replace the clean gas induction valve. Install O-ring seal (9).
Show/hide table
Illustration 3 g01265786 - Install O-ring seals (8) onto valve (7). Install valve (7). Tighten valve (7) to a torque of
50 ± 5 N·m (37 ± 4 lb ft) . Install coil assembly (6) and nut (5). Tighten nut (5) to a torque of20 ± 3 N·m (15 ± 2 lb ft) .Show/hide table
Illustration 4 g01299978 - Install cover (4). Install bolts (3).
Show/hide table
Illustration 5 g01299977 - Install O-ring seal (2).
Show/hide table
Illustration 6 g01299976 - Install O-ring seal (1).
Show/hide table
| |
| Illustration 1 | g01265789 |
End By:
- Install the clean gas induction valve. Refer to Disassembly and Assembly, "Clean Gas Induction Valve - Install".
Caterpillar Information System:
C13 Engine Air Compressor - Remove and Install
3500B Industrial Engines with the ADEM 3 Electronic Control Module Intermediate Speed Switch
C15 On-Highway Engine Fuel Filter Base
2006/07/01 A New Field Service Kit for Alternators is Now Available {1405, 7555}
C13 On-highway Engine Fuel Priming Pump
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Abbreviations and Acronyms
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Overview
C9 Marine Engines and C9 Marine Generator Sets Injection Actuation Pressure Sensor
C7 On-Highway Engine Air Inlet Cover - Remove and Install
2006/08/07 A New Oil Pump for the Hydrax System is Used {1716, 5073}
C27 and C32 Engines for Caterpillar Built Machines Camshaft - Install - C27
C13 Engine Boost Pressure Sensor - Remove and Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Configuration
TH48-E70 Petroleum Transmission Lifting and Tying Down the Transmission
C7 On-Highway Engine Flywheel Housing - Remove and Install
C7 On-Highway Engine Coolant Temperature Sensor - Remove and Install
C7 On-Highway Engine Fuel Pressure Sensor - Remove and Install - Main
C9 On-highway Engine Electronic Unit Injector Wiring
C7 On-Highway Engine Fuel Pressure Sensor - Remove and Install - Pilot
3500B Industrial Engines with the ADEM 3 Electronic Control Module Overspeed Verify Switch
C13 Engine Crankshaft Position Sensor - Remove and Install
Mechanical Application and Installation Guide for TH48-E70 Petroleum Transmissions{3030, 3101} Mechanical Application and Installation Guide for TH48-E70 Petroleum Transmissions{3030, 3101}
C13 Engine Fuel Temperature Sensor - Remove and Install
C4.4 Industrial Engine Electronic Control System