Alternator - Remove and Install
拆卸步骤
Show/hide table
不断开蓄电池可能会造成人身伤害。 先断开蓄电池负极电缆。 然后断开蓄电池正级电缆。 如果没有断开蓄电池的话,正极电源线可能会产生花火。 火花可能会导致蓄电池爆炸或起火。 |
- 断开蓄电池负极接线端。 请参阅操作和保养手册, "蓄电池或蓄电池电缆 - 断开"。
- 拆下螺栓 (1) 。 拆下护罩 (2) 。
Show/hide table
图 1 | g01256155 |
- 在连接到交流发电机 (3) 的线束组件上作一个识别标记以便于安装。 拆下螺栓 (4) 和螺母 (5) 。 从交流发电机 (3) 上断开线束组件 (6) 。
Show/hide table
图 2 | g01256156 |
- 松开调节连杆 (13) 上的螺母 (12) 。
Show/hide table
图 3 | g01242411 |
- 松开螺栓 (9) 上的螺母。 将交流发电机 (3) 的底部推向缸体。 拆下交流发电机皮带轮上的 V 型皮带。
- 拆下螺栓 (9) 和螺栓 (11) 。 拆下交流发电机 (3) 。
- 将螺母 (10) 和交流发电机皮带轮从交流发电机 (3) 上拆下。
- 拆下螺母 (7) 和支架 (8) 。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 155-0695     | 螺纹锁固胶     | -     |
- 安装交流发电机皮带轮和螺母 (10) 。 拧紧螺母 (10) 至扭矩为 102 ± 7 N·m (75 ± 5 lb ft)。
Show/hide table
图 4 | g01242411 |
- 将支架 (8) 在螺柱上安置到位。 将工具 (A) 涂抹在螺柱的螺纹上。 安装螺母 (7) 并拧紧螺母 (7) 至扭矩为 70 ± 5 N·m (58 ± 4 lb ft)。
- 将交流发电机 (3) 在支架 (8) 上安放到位并安装螺栓 (9) 。
- 将调节连杆 (13) 在交流发电机 (3) 上安放到位。 安装螺栓 (11) 并拧紧螺栓 (11) 至扭矩为 88.4 ± 6.8 N·m (65 ± 5 lb ft)。
- 安装 V 形皮带。 张紧 V 形皮带。 请参阅测试与调整, "皮带张紧度表"。
- 拧紧螺母 (12) 至扭矩为 30 ± 15 N·m (22 ± 11 lb ft)。
- 将线束组件 (6) 安装在交流发电机 (3) 上。 拧紧螺母 (5) 至扭矩为 6.2 ± 0.6 N·m (55 ± 5 lb in)。 拧紧螺栓 (4) 至扭矩为 2.25 ± 0.25 N·m (20 ± 2 lb in)。
Show/hide table
图 5 | g01256156 |
- 安置护罩 (2) 并安装螺栓 (1) 。
Show/hide table
图 6 | g01256155 |
- 连接蓄电池负极接线端。 请参阅操作和保养手册, "蓄电池或蓄电池电缆 - 断开"。
Caterpillar Information System:
C175 Generator Set Engines Engine Oil Pump - Remove
C15 and C18 Generator Set Engines Electronic Control Module - Remove and Install
3512C and 3516C Engines Starting Motor System
3512C and 3516C Engines Speed Control
2006/04/17 Slide Sledge Heavy Equipment Repair Tools Are Now Available {0599, 0644}
C7 Marine Engines Oil Cooler (Transmission, Auxiliary) - Remove and Install
3512C and 3516C Engines Pulse Width Modulated Sensor
3500 Engines Balancer Group (Front) - Remove and Install - 3508C Engine
D Series Excavator Monitoring System Performance Mode
3406E, C-10, C-12, C-15, C-16 Truck Engines Reference Material
C13, C15, and C18 Generator Set Engines CID 1690 FMI 08 Throttle #2 Position Sensor abnormal frequency, pulse width, or period
3500 Engines Housing (Front) - Install
CX31 and CX31 HT On-Highway Transmissions General Troubleshooting Information
Hose and Coupling Assembly and Repair Process Guide{0684, 3016, 3103, 3154, 4133, 4257, 4304, 5057, 7554} Hose and Coupling Assembly and Repair Process Guide{0684, 3016, 3103, 3154, 4133, 4257, 4304, 5057, 7554}
C3.3 and C4.4 Rental Generator Sets Additional Messages
C15 and C18 Generator Set Engines CID 0091 FMI 08 Throttle Position signal abnormal
C175 Generator Set Engines Engine Oil Pump - Install
C15 and C18 Generator Set Engines Electric Starting Motor - Remove and Install
3512C and 3516C Engines Sensor Supply
C175 Generator Set Engines Air Inlet Manifold - Remove and Install
3176C and 3196 Engines for Caterpillar Built Machines Belt Tensioner
3512C and 3516C Engines Analog Sensor (Passive)
C175-16 and C175-20 Engines for Caterpillar Built Machines Fuel Pump (High Pressure) - Remove and Install
C15 and C18 Generator Set Engines Fan Drive - Remove