Hotkeys
Hotkeys allow you to command UPS View to perform various functions without having to access menus or use the computer mouse.
Standalone hotkeys let you command UPS View to perform various functions without having to press and hold the Control (Cntrl) key or Alternate (Alt) key.
- B = Silence Display Buzzer
- \ = Enable Printing of Startup Errors
Control (Cntrl) and Alternate (Alt) Hotkeys
The "Cntl" hotkey allows you to command UPS View to perform the following functions by pressing the "Cntl" key plus an alpha or symbol key.
- Control + H = Show Hotkeys
- Control + A = Send Tile defs
- Control + _ = Send Op Params
- Control + P = Clear Password
- Control + O = Enter Online Mode
- Control + B = Enter Bypass Mode
- Control + S = Enter Bypass Spindown Mode
- Control + X = Brake Rotor
- Control + N = Show Revision Info
- Control + Z = Dump Setpoints
- Control + D = Download Event Log
- Control + J = Show Diagnostic data
- Control + G = Dump IGBT Currents
- Control + \ = Show Bypass Status
- Control + Y = Read Modem Configuration
- Control + R = Reset the Processor
- Control + F = Get Password Seed and Serial Number
- Control + W = Toggle Modem Hook Status
The "Alt" hotkey allows you to command UPS View to perform the following functions by pressing the "Alt" key plus an alpha or symbol key.
- ALT + R = Enter Regulation Only mode
- ALT + S = Enter AVR Spin-down Mode
- ALT + Z = Report Non-default Op Params
- ALT + G = AVR Demand FPGA Reading
- ALT + T = Show Telemetry and Status Registers
- ALT + U = Show B-N (or Ground) Voltage
- ALT + I = EPO Switch Status
- ALT + J = Show Ethernet Statistics
- ALT + N = Toggle Show Notification Debug
- ALT + P = Cancel Paging
- ALT + E = Ethernet Loopback Test
This command brings up the "About UPS View" window. The version number, serial number, and the IP address or ComPort is displayed in the window.
Show/hide table
| |
| Illustration 1 | g01149590 |
Caterpillar Information System:
UPS View User Guide User Operations
2005/03/07 Improved Alternator Adjusting Rod {1405}
C7 and C9 Marine Engines Analog Sensor Supply Circuit - Test
UPS View User Guide Remote Notification
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C9 Engines for Caterpillar Built Machines Unit Injector - Install
C9 Engines for Caterpillar Built Machines Unit Injector - Remove
UPS View User Guide Log Files
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Install - Two Cylinder
C3.3 and C4.4 Generator Sets Fuel Injection Nozzles - Test/Exchange
D Series Excavator Monitoring System Password Change Mode
3406E, C12, C15 and C18 Marine Engines Can Not Reach Top Engine RPM
2005/05/23 New Hoses for the Jacket Water Heater {1383}
C7 and C9 Marine Engines CAN Data Link Circuit - Test
C7 and C9 Marine Engines Digital Sensor Supply Circuit - Test
C7 and C9 Marine Engines Electrical Power Supply Circuit - Test
C7 and C9 Marine Engines Engine Pressure Sensor Open or Short Circuit - Test
C7 and C9 Marine Engines Engine Speed/Timing Sensor Circuit - Test
C7 and C9 Marine Engines Engine Temperature Sensor Open or Short Circuit - Test
C7 and C9 Marine Engines Indicator Lamp Circuit - Test
C7 and C9 Marine Engines Injector Solenoid Circuit - Test
C7 and C9 Marine Engines Switch Circuits - Test
C7 and C9 Marine Engines Transmission Oil Temperature Sensor Open or Short Circuit - Test
C11 and C13 Petroleum Engines Cylinder Head - Remove