Prelubrication Oil Pump - Install
Installation Procedure
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Use two people in order to position prelubrication pump (5). The weight of prelubrication pump (5) is approximately 34 kg (76 lb).
Show/hide table
 | |
| Illustration 1 | g01113847 |
- Install nuts (7) .
- Connect harness assembly (4) .
- Connect cable assemblies (3) and (6) .
- Connect tube assembly (8) .
- Connect hose assembly (2) .
Show/hide table
 | |
| Illustration 2 | g01113833 |
- Install nuts (1) .
End By:
- Install the front center bottom guard. Refer to Disassembly and Assembly, "Bottom Guard - Install".
- Install the left engine side guard. Refer to Disassembly and Assembly, "Engine Side Guards - Remove and Install".
Caterpillar Information System:
AP-1055D and BG-2455D Asphalt Pavers Daily Inspection
CB-214E, CB-224E and CB-225E Vibratory Compactors Machine Systems Piston Pump (Propel) - Assemble
CB-214E, CB-224E and CB-225E Vibratory Compactors Machine Systems Piston Pump (Propel) - Disassemble
16M Series 3 and 18M Series 3 Motor Graders Wheel Lean Bearings - Lubricate
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Engine Supplement Muffler - Remove and Install
C9.3 Engine for Caterpillar Built Machines Valve Mechanism Cover
12M, 140M and 160M Motor Graders Hydraulic and Steering System Visual Inspection
583T Pipelayer Engine Supplement Prelubrication Oil Pump - Remove
416E, 420E and 430E Backhoe Loaders Power Train System Pressure - Release
267B, 277B and 287B Multi Terrain Loaders Machine Systems General Information
AP-1055D and BG-2455D Asphalt Pavers Lifting and Tying Down the Machine
Bench Test Procedure for Hydraulic Piston Pumps{3108, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3108, 5070}
12H, 140H and 160H Motor Graders Power Train Tandem and Cover - Remove and Install
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Engine Supplement Radiator, Refrig Condenser, and Hyd and TMSN Oil Cooler - Remove
143H and 163H Motor Graders Power Train Tandem and Cover - Remove and Install
C9 Engines for Caterpillar Built Machines Vibration Damper and Pulley
3508C, 3512C and 3516C Marine Engines Engine Oil Filter Housing - Disassemble
3508C, 3512C and 3516C Marine Engines Engine Oil Filter Housing - Assemble
2004/11/08 New Engine Software Corrects Warnings of Air Filter Inlet Air Restriction {7620}
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Engine Supplement Radiator, Refrig Condenser, and Hyd and TMSN Oil Cooler - Install
PS-360C Pneumatic Compactor Machine System Additive Spray System Troubleshooting
PS-360C Pneumatic Compactor Machine System Check Valves (Air on the Run) - Check
583T Pipelayer Power Train Main Drive Shaft - Remove and Install
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Engine Supplement Hydraulic and Transmission Oil Cooler - Remove