2003/05/05 Caterpillar


New QuickEvac High Speed Oil Change Arrangements Are Available {1325}

Usage:

769C 01X


Machine Engines:
  • C-9
  • 3046
  • 3054
  • 3056
  • 3056 and 3064
  • 3066
  • 3116
  • 3126
  • 3176
  • 3196
  • 3306
  • 3406
  • 3408
  • 3412
  • 3456
  • 3508
  • 3512
  • 3516
  • Service Magazine, SEPD0856, 25 September 2006, "New Cat QuickEvac High Speed Oil Change Arrangements Are Available". Disregard this article. See the article that follows.

    New attachments have been developed for Caterpillar machine models and engine arrangements. The QuickEvac System automates engine oil change intervals. Automation will reduce the amount of time that is spent on regular service of the engines. QuickEvac technology can evacuate most oil sumps in less than 60 seconds. The QuickEvac system can be especially economical on machines with drain plugs that are extremely difficult to reach.

    The system uses compressed air to purge the used oil out of the filter and into the oil pan. The QuickEvac pump will then evacuate the old engine oil into environmentally safe containers. The filters can then be removed with minimal engine oil in order to eliminate oil leakage. Once the new filters are installed, fresh oil is pumped into the engine. The new oil is added through the filters in order to ensure that there is no contamination.

    The QuickEvac system will also prevent an engine start without proper lubrication. The prelube cycle pressurizes the lubrication system before the engine is started. The QuickEvac pump is activated once the keyswitch is turned to the ON position. This pump pressurizes the lubrication system in order to ensure proper lubrication. The keyswitch must be held in the START position in order to operate the QuickEvac system. While the QuickEvac pump is energized, an indicator light that is located on the dashboard will be illuminated. Once the entire lubrication system is pressurized, the starter will be engaged.

    Dealers have several options in order to source the QuickEvac system for Caterpillar machines. Retrofit kits are available for conversions at dealerships on existing machines and on new machines. If the QuickEvac system has been released as a factory installed attachment, the system can be installed before the delivery to the dealer. Information about new installations on machines and availability of parts for a retrofitting can be found by contacting RPM Industries.

    Caterpillar Information System:

    3116 and 3126 Truck Engines Rocker Shaft and Pushrod - Install
    3116 and 3126 Truck Engines Rocker Shaft - Assemble
    3116 and 3126 Truck Engines Rocker Shaft - Disassemble
    3500 Marine Engines Accumulator Pressure - Test
    2003/08/01 A Pin for the Rocker Shaft Is Now Available for Parts Service {1102}
    2003/05/01 New Cylinder Liner {1216}
    3116 and 3126 Truck Engines Rocker Shaft and Pushrod - Remove
    C15 and C18 Petroleum Generator Sets Mounting and Dismounting
    3406E and 3456 Generator Set Engines E173 High Exhaust Temperature Warning
    3500B Series II Marine Engines E100 Low Engine Oil Pressure Warning
    3500B Series II Marine Engines E040 Low Engine Oil Pressure Shutdown
    Caterpillar On-Highway Diesel Engine Fluids Recommendations Reference Material
    G3520C and G3520E Generator Set Engines Water Pump - Remove
    G3520C and G3520E Generator Set Engines Water Pump - Install
    3618 Engine Aftercooler Core - Clean/Test
    Inspection and/or Repair Procedure to Replace Broken Crankshafts in C-15, C-16, C15, 3406C, 3406E, and 3456 Engines{1202} Inspection and/or Repair Procedure to Replace Broken Crankshafts in C-15, C-16, C15, 3406C, 3406E, and 3456 Engines{1202}
    3618 Engine Turbocharger - Inspect
    2003/05/01 New Front Crankshaft Seals and New Rear Crankshaft Seals are Now in Production {1160, 1161}
    2003/05/01 New Front Crankshaft Seals and New Rear Crankshaft Seals are Now in Production {1160, 1161}
    G3500 Engines Prelube Pump - Electric
    G3520C and G3520E Generator Set Engines Cylinder Head - Disassemble
    G3520C and G3520E Generator Set Engines Cylinder Head - Assemble
    G3500 Engines Prelube Pump - Air
    C27 and C32 Generator Set Engines CID 0100 FMI 10 Engine Oil Pressure Sensor abnormal rate of change
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.