Inlet and Exhaust Valve Guides - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-9169 | Valve Guide Driver | 1 |
Start By:
- Remove the inlet valves and the exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) in order to remove the valve guides from the cylinder head.
- Repeat the procedure for the remaining valve guides.
Show/hide table
Illustration 1 | g00632175 |
Typical example |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-9169 | Valve Guide Driver | 1 |
B | 9U-6220 | Stop Collar | 1 |
C | 157-3720 | Valve Seat Cutter | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Put the valve guide in position. Carefully tap the valve guide in order to start the installation. Use Tooling (A) and Tooling (B) to seat the valve guide in the cylinder head.
Note: After installing the unfinished valve guides and valve seat inserts, you must ream the valve guides and valve seat inserts to the finished diameter. The valve guides and valve seat inserts are cut and reamed in one operation. This operation is performed by using the 157-3720 Valve Seat Cutter. Refer to Specifications, RENR2401, "Cylinder Head Valves" for the finished diameter of the valve guides and valve seat inserts.
- Check the protrusion of the valve guides. The valve guides should protrude
14.85 to 15.15 mm (0.585 to 0.597 inch) above the valve spring recess. - Repeat the procedure for the remaining valve guides.
Show/hide table
Illustration 2 | g00632176 |
Typical example |
End By:
- Install the inlet valves and the exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".
Caterpillar Information System:
3412E and C30 Marine Engines Front Power Take-Off (FPTO)
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3612 and 3616 Fast Vessel Engines Engine Mounts - Check
G3606 and G3608 Engines Water Pump Seal - Install
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
3054 and 3056 Industrial and Generator Set Engines Inlet Manifold - Install
3606 and 3608 Engines Cooling System Operation
3612 and 3616 Fast Vessel Engines Hourly Performance Log
3054 and 3056 Industrial and Generator Set Engines Inlet Manifold - Remove
3054 Engine for Caterpillar Built Machines Turbocharger - Assemble
G3606 and G3608 Engines Water Pump Seal - Remove
3054 Engine for Caterpillar Built Machines Turbocharger - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump Drive - Remove
3054 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3612 and 3616 Fast Vessel Engines Air Shutoff - Test
3054 Engine for Caterpillar Built Machines Engine Oil Pump - Remove
3054 Engine for Caterpillar Built Machines Alternator - Remove and Install
3412E and C30 Marine Engines Electronic Control System
G3606 and G3608 Engines Water Manifold - Remove and Install
3600 Heavy Fuel Engines Metal Particle Detector - Inspect
3054 Engine for Caterpillar Built Machines Engine Oil Pump - Install
3054 Engine for Caterpillar Built Machines Water Pump - Remove
Caterpillar On-Highway Diesel Engine Fluids Recommendations Conventional Coolant/Antifreeze Cooling System Maintenance
G3606 and G3608 Engines Prelubrication Oil Pump - Remove