Seat - Remove and Install
Removal Procedure
Start By:
- Tilt the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
- Remove two nuts (1) and the washers.
Show/hide table
Illustration 1 | g00593838 |
- Disconnect electrical connection (2) .
- Remove grommet (3) .
- Remove three bolts (4) and remove the access panel.
Show/hide table
Illustration 2 | g00794887 |
- Disengage the cab support (5) and lower the cab.
Show/hide table
Illustration 3 | g00594433 |
- Remove two nuts (6) and the washers under the front of the seat.
Show/hide table
Illustration 4 | g00590150 |
- Remove seat (7). The weight of the 142-9304 suspension seat is 20 kg (44 lb). The weight of the 142-9309 static seat is 7 kg (15.5 lb).
Show/hide table
Illustration 5 | g00794891 |
Note: For additional information concerning the seat, refer to Service Manual, SENR6615, "Contour Series Seat".
Installation Procedure
- Place seat (7) into position. The weight of the 142-9304 suspension seat is 20 kg (44 lb). The weight of the 142-9309 static seat is 7 kg (15.5 lb).
Show/hide table
Illustration 6 | g00794891 |
- Install two nuts (6) and the washers under the front of the seat.
Show/hide table
Illustration 7 | g00590150 |
- Raise the cab and engage the cab support (5) .
Show/hide table
Illustration 8 | g00594433 |
- Place the access plate into position and install three bolts (4) .
Show/hide table
Illustration 9 | g00794887 |
- Install two nuts (1) and the washers.
Show/hide table
Illustration 10 | g00593838 |
- Install grommet (3) .
- Connect electrical connection (2) .
End By: Lower the cab. Refer to Disassembly and Assembly, "Cab - Tilt".
Caterpillar Information System:
M316C, M318C and M322C Excavators and M318C and M322C Material Handlers Operating Technique Information
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0660 - FMI 02
TH103 Telehandler Hydraulic System Hydraulic System Troubleshooting
561M Pipelayer Hydraulic Tank and Filter - Assemble
2001/05/14 Modifications to the Implement Pump Are Used on Forwarders {5070, 5084}
TK711 Track Feller Buncher, TK721 Track Feller Buncher, TK722 Track Feller Buncher and TK732 Track Feller Buncher Machine Systems Pump Head (Main)
769D Off-Highway Truck/Tractor and 771D Quarry Truck Suspension Cylinder - Check
3176C Engine for Caterpillar Built Machines Travel Alarm System - Test
Instructions for the Installation of the 174-1508 Electric Motor {5927} Instructions for the Installation of the 174-1508 Electric Motor {5927}
TK1051 Track Feller Buncher Machine System Pump Head (Saw)
777D HAA Off-Highway Truck Towing With Power Train Failure
2001/05/07 Correction to Systems Operation, Testing and Adjusting , "Tilt Cylinder Head End Relief Valves" {5117}
TL3 Series Disk Rippers Plate Locations and Film Locations
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Transmission
735, 740 and 740 EJECTOR Articulated Trucks Braking System Service Brake
2001/06/18 Door Stop Has Been Relocated {7252, 7253}
2001/06/18 New Retaining Ring Kit for the Pilot Control Actuator Group on the Hoist Control Valve Group is Now Available {5078, 5136}
TH103 Telehandler Hydraulic System Hydraulic System Pressure - Release
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems General Information Table
2001/05/14 Correction to Testing and Adjusting, SENR1272 for the High Pressure Stall Test {5070}
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Bearing End Play (Piston Pump) - Adjust
735, 740 and 740 EJECTOR Articulated Trucks Engine Supplement Engine - Install
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0661 - FMI 02
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0662 - FMI 02