824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Machine Systems Caterpillar

Assembly Procedure

Show/hide table

Illustration 1	g00670525

1. Use the proper equipment to handle bearing (54). Heat bearing (54) to a maximum temperature of 121 °C (250 °F). Install bearing (54) onto the shaft (49).
   Show/hide table

   Illustration 2	g00670361

2. Use the proper equipment to handle the bearing cup. Lower the temperature of bearing cup (53) and install the bearing cup in pump body (27).
   Show/hide table

   Illustration 3	g00670360

3. Inspect the O-ring seals on plugs (52). Replace the O-ring seals, if necessary. Install two plugs (52) in pump body (27).
   Show/hide table

   Illustration 4	g00670531

   Show/hide table

   Illustration 5	g00670532

4. Install snap ring (50). Use Tooling (A) to install seal (51) (not shown).
   Show/hide table

   Illustration 6	g00670298

5. Install shaft assembly (49).

6. Use the following steps to determine the proper preload on the bearings of the pump assembly.
   Show/hide table

   Illustration 7	g00669728

   1. Use the proper equipment to handle the bearing cup. Lower the temperature of bearing cup (30) and install the bearing cup in head assembly (26).
      Show/hide table

      Illustration 8	g00670604
      Typical Example

   2. Install adjustment shim (33) and bearing (32) onto shaft (49).
      Show/hide table

      Illustration 9	g00670605

   3. Position head assembly (26) onto pump body (27).
      Show/hide table

      Illustration 10	g01088808

   4. Use Tooling (C) to measure the distance between the head and the pump housing.

   5. Take measurements at three equal intervals on the surface between the head and the pump housing.

   6. The average of the three dimensions should be between zero and 0.05 mm (.002 inch).

   7. If necessary, grind adjustment shim (33) in order to obtain the correct dimension between the head and the pump housing. It may be necessary to replace the shim with a new part.
      Show/hide table

      Illustration 11	g00670625

   8. Install four bolts (25) in the head and pump housing (27). Tighten bolts (25) to a torque of 100 ± 20 N·m (75 ± 15 lb ft).
      Show/hide table

      Illustration 12	g00670626

   9. Use Tooling (D), (E), and (F) to check end play in shaft (49). If end play exists in the shaft assembly, repeat Step 6 until the correct dimension between the head and the pump housing is reached.

   10. Remove bolts (25) and head assembly (26) from pump body (27). Remove bearing (32) and adjustment shim (33) from shaft (49).

   11. Proceed with the assembly of the fan drive pump.
   Show/hide table

   Illustration 13	g00670223

7. Install two swashplate bearings (48).
   Show/hide table

   Illustration 14	g00670207

8. Install spring (47).
   Show/hide table

   Illustration 15	g00670206

9. Install swashplate (46).
   Show/hide table

   Illustration 16	g00670205

   Note: Note that there is a correct connection of the piston rod and the swashplate.

10. Install piston rod (45).
    Show/hide table

    Illustration 17	g00670204

11. Install the control piston (44).
    Show/hide table

    Illustration 18	g00669745

    Show/hide table

    Illustration 19	g00669744

    Show/hide table

    Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment.

    Note: There is spring force against lock ring (43). When lock ring (43) is not seated properly, the spring force will be released. Installation of the internal components in barrel (38) should be performed in a press. This is done in order to retain spring (42) and lock ring (43).

12. Install pins (40), guide (41) and spring (42) in barrel (38).

13. Use a press and Tooling (A) to compress the spring (42) in barrel assembly (38).

14. Use Tooling (B) to install retaining ring (43).

15. Slowly release compression on spring (42). Make sure that the retaining ring (43) is seated properly.
    Show/hide table

    Illustration 20	g00669743

16. Install retaining ball (39) on barrel assembly (38).
    Show/hide table

    Illustration 21	g00669741

17. Install piston assembly (37) in barrel assembly (38).
    Show/hide table

    Illustration 22	g00669742

18. Install rotary group (36) onto the shaft. Make sure that the splines are aligned properly.
    Show/hide table

    Illustration 23	g00669732

19. Inspect the O-ring seal on plug (34). Replace the O-ring seal, if necessary. Install plug (34).
    Show/hide table

    Illustration 24	g00669731

20. Install the adjustment shim (33).
    Show/hide table

    Illustration 25	g00669730

21. Install bearing (32) on the shaft.
    Show/hide table

    Illustration 26	g00669729

22. Install O-ring (31).
    Show/hide table

    Illustration 27	g00669727

23. Install O-ring seal (28) and port plate (29) on head assembly (26).
    Show/hide table

    Illustration 28	g00669722

24. Install head assembly (26) and four bolts (25). The torque for the bolts (25) is 100 ± 20 N·m (75 ± 15 lb ft).
    Show/hide table

    Illustration 29	g00670203

25. Install spool (23) in compensator valve (1). Install spacer (24) onto plug (22).

26. Install plug (22) in compensator valve (1). The torque for the plug (22) is 30.5 ± 1.5 N·m (23 ± 1 lb ft).
    Show/hide table

    Illustration 30	g00670201

27. Install O-ring seal (17) to plug (16). Install plate (18), spring (19), spring (20), and guide (21) in compensator valve (1).

28. Install plug (16) in compensator valve (1). The torque for the plug (16) is 100 ± 5 N·m (75 ± 3 lb ft).
    Show/hide table

    Illustration 31	g00670198

29. Install spool (14) in compensator valve (1). Install spacer (15) on plug (13).

30. Install plug (13) in compensator valve (1). The torque for the plug (13) is 30.5 ± 1.5 N·m (23 ± 1 lb ft).
    Show/hide table

    Illustration 32	g00670195

31. Install O-ring seal (8) to plug (7). Install plate (9), spring (10), spring (11), and guide (12) in compensator valve (1).

32. Install plug (7) in compensator valve (1). The torque for the plug (7) is 80 ± 5 N·m (58 ± 3 lb ft).
    Show/hide table

    Illustration 33	g00670190

33. Inspect the O-ring seals on plugs (5). Replace the O-ring seals, if necessary. Install two plugs (5) in compensator valve (1).
    Show/hide table

    Illustration 34	g00670188

34. Inspect the O-ring seals (4) and replace the O-ring seals, if necessary. Install three O-ring seals (4) on compensator valve (1).
    Show/hide table

    Illustration 35	g00669721

35. Install four bolts (2) and pressure and flow compensator valve (1) to fan drive pump (3). The torque for bolts (2) is 34 ± 3 N·m (25 ± 2 lb ft).

End By:

1. Install the fan drive pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic Fan) - Install".