Engine Oil Level - Check
Show/hide table
 |
热油和热的部件可能会导致人员受伤。 请勿让热的液压油或热的零部件与皮肤接触。 |
Show/hide table
| 注意 |
|---|
发动机曲轴箱注油时，油不要过少或过满。 任何一种情况都会造成发动机损坏。 |
注: 在拿开油尺/加油口盖之前，应将其周围清洁干净。
Show/hide table
 | |
| 图 1 | g00701412 |
- 打开发动机室左侧检修门 (1) 。
- 在起动发动机前，发动机停止时检查"发动机停机 "一侧的油尺 (2) 将油位保持在"添加"（ADD）和"满(FULL)"（FULL）标记之间。
起动发动机，在发动机运转时检查"发动机运转 "一侧的油尺 (2) 将油位保持在"添加"（ADD）和"满"（FULL）标记之间。
Show/hide table
 | |
| 图 2 | g00701618 |
- 拆下油加注口盖 (3) 。必要时，加油。
Show/hide table
 | |
| 图 3 | g00723833 |
- 清洁油加注口盖 (3) 并安装油加注口盖 (3) 。
- 关闭发动机室的检修门 (1) 。
Caterpillar Information System:
834G Wheel Dozer and 836G Landfill Compactor Electrohydraulic System MID 082 - CID 0296 - FMI 12
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Brake Control Valve (Service)
3034 Engine for Caterpillar Built Machines Crankshaft Gear - Remove and Install
140H and 160H Motor Graders Circle Top - Lubricate
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0352 - FMI 13
988G Wheel Loader Electrohydraulic System MID 082 - CID 0650 - FMI 12
140H and 160H Motor Graders Circle Drive Pinion Teeth - Lubricate
834G Wheel Dozer and 836G Landfill Compactor Electrohydraulic System MID 082 - CID 0353 - FMI 04
140H and 160H Motor Graders Circle Drive Oil Level - Check
24H Motor Grader Engine Crankcase Breather - Clean
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0353 - FMI 13
980G Wheel Loader, 824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Implement Electronic Control System MID 082 - CID 0353 - FMI 01
797 Off-Highway Truck Power Train Relief Valve (Rear Axle Motor Unloader) - Assemble
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Transfer Gears - Disassemble
584 and 584HD Forwarders General Hazard Information
24H Motor Grader Engine Oil Sample - Obtain
2000/04/24 Correction to Testing and Adjusting for the Stall Test {1000, 3030, 3101}
988G Wheel Loader Electrohydraulic System MID 082 - CID 0352 - FMI 04
988G Wheel Loader Electrohydraulic System MID 082 - CID 0353 - FMI 03
12H Motor Grader Circle Drive Pinion Teeth - Lubricate
2001/01/29 New Improved Transmission Control {3168}
2000/04/24 The Grab Handle for Use with the Cab Door Has Been Redesigned {7308}
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Piston Pump Servo Neutral - Test and Adjust
2000/11/27 Clearances in the Torque Converter Are Changed {3101}