Usage:
Cylinder Head Bolt Tightening Sequence
Remove Cylinder Head Assembly
START BY:
a. remove rocker shaft assemblies and push rods
b. remove water temperature regulator
c. remove aftercooler housing
d. remove fuel injection lines
e. remove exhaust manifold
1. Remove bolts (1) from the alternator bracket.
2. Remove the bolts that hold plate (3), and remove the plate.
3. Disconnect water line (2) from the air compressor.
NOTE: Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt.
4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.
5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
| NOTICE |
|---|
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves. |
6. Remove the gasket and seals from the spacer plate.
Install Cylinder Head Assembly
NOTE: Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate.
1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2).
2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.
3. Put 5P3931 Anti-Seize Compound on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration A87019X1 on page 6-119.
a. Tighten bolts 1 through 20 in number sequence to a torque of 270 ± 25 N·m (200 ± 18 lb.ft.).
b. Tighten bolts 1 through 20 in number sequence to a torque of 450 ± 20 N·m (330 ± 15 lb.ft.).
c. Tighten bolts 1 through 20 in number sequence to a torque of 450 ± 20 N·m (330 ± 15 lb.ft.) by hand.
d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.
e. Tighten bolts 21 through 26 in number sequence to a torque of 270 ± 25 N·m (200 ± 18 lb.ft.).
f. Tighten bolts 21 through 26 in number sequence to a torque of 450 ± 20 N·m (330 ± 15 lb.ft.).
g. Tighten bolts 21 through 26 in number sequence to a torque of 450 ± 20 N·m (330 ± 15 lb.ft.) by hand.
h. Tighten the 3/8" bolts to a torque of 43 ± 7 N·m (32 ± 5 lb.ft.).
NOTE: If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 ± 4 N·m (18 ± 3 lb.ft.).
4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 mm (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 ± 4 N·m (21 ± 3 lb.ft.).
5. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And Push Rods.
6. Install the valve covers. See Install Valve Covers.
7. Install plate (4).
8. Connect the water line to the air compressor.
9. Install bolts (5) for the alternator bracket.
END BY:
a. install exhaust manifold
b. install fuel injection lines
c. install aftercooler housing
d. install water temperature regulator