Swing Drive - Remove and Install
参考: 专门说明书, "目视维修步骤 - 颜色和符号" M0066576。
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 154-6184 | 顶出螺栓 | 2 |
| B | 477-3149 | 吊环螺栓组件 | 3 |
| C | 8C-8422 | 密封胶 | - |
| D | - | Loctite C5A 防咬合剂(1) | - |
| - | Loctite 8008 防咬合剂(2) | - | |
Show/hide table
| (1) | 北美洲 |
| (2) | 北美以外 |
开始:
- 拆下回转驱动马达。
Show/hide table
| |
| 图 1 | g06243396 |
Show/hide table
| |
| 图 2 | g06243403 |
Show/hide table
| |
| 图 3 | g06243624 |
- 按与拆卸相反的顺序安装回转驱动。
Show/hide table
| |
| 图 4 | g06243687 |
|
组装前，必须先清洁配合面再涂抹密封剂。 | |
Show/hide table
| |
| 图 5 | g06243698 |
Caterpillar Information System:
C32 Tier 4 Final Marine Commercial Engines Speed/Timing - Test
320 GC, 320 and 323 Excavator Machine Systems Check Valve (Return Makeup)
336, 336 GC and 340 Excavator Systems Swing System
C27 and C32 Engine for MD6250 and MD6310 Drill Fuel Priming Pump - Test
320GC and 320 Excavator Engine Supplement Air Inlet Elbow - Remove and Install - Twin Turbo
320GC and 320 Excavator Engine Supplement Air Inlet Elbow - Remove and Install - Turbo
Procedure to Install Jump-Start Wiring Kits on Certain Excavators {1408, 1463} Procedure to Install Jump-Start Wiring Kits on Certain Excavators {1408, 1463}
CX38–P892 Petroleum Transmission Pump Drive - Remove
Procedure to Install Pedal Kits on Certain Next Generation Hydraulic Excavators {5462} Procedure to Install Pedal Kits on Certain Next Generation Hydraulic Excavators {5462}
320GC, 320 and 323 Excavators Machine Systems Track - Separate and Connect
Installation Procedure for Dual Exit Rear Window Kit on Certain Next Generation Excavators {7310} Installation Procedure for Dual Exit Rear Window Kit on Certain Next Generation Excavators {7310}
320GC, 320 and 323 Excavators Machine Systems Hydraulic Lockout Control - Remove and Install
C32 Tier 4 Final Marine Commercial Engines Speed Control - Test
320GC and 320 Excavator Engine Supplement Exhaust Back Pressure Valve - Remove and Install
An Improved Factory Assembly Process Has Been Implemented on Certain Telehandlers {3030, 3061, 3064, 3066, 3101, 3160} An Improved Factory Assembly Process Has Been Implemented on Certain Telehandlers {3030, 3061, 3064, 3066, 3101, 3160}
C32 Tier 4 Final Marine Commercial Engines Solenoid Valve - Test - Aftertreatment
C32 Tier 4 Final Marine Commercial Engines Solenoid Valve - Test - Engine
336, 336 GC and 340 Excavator Systems Check Valve (Return Makeup)
320GC, 320 and 323 Excavators Machine Systems Bucket Cylinder - Disassemble
C13, C15, and C18 Tier 4 Final Engines Diesel Exhaust Fluid Pump
320GC, 320 and 323 Excavators Machine Systems Bucket Cylinder - Assemble
320GC, 320 and 323 Excavators Machine Systems Stick Cylinder - Disassemble
XQ125 Generator Set Engine Crankcase Breather Element - Replace
XQ125 Generator Set Setup