Nitrogen Oxide Sensor - Replace
Note: During installation and handling of the sensor, follow the parameters listed below:
- Do not expose the sensor to any fluids
- Do not contact the sensing element when power is applied to the sensor. Contact with the sensing element may result in injury. The sensing element is heated to a minimum of
100° C (212° F) . - Do not use any lubricant on any part of the sensor other than the threads. Do not use unapproved thread lubricant. Do not apply more anti-seize to new parts. If more anti-seize is necessary for pre-installation, use only nickel based anti-seize or non-metallic anti-seize. Apply anti-seize to the threads only and avoid contaminating the sensor head.
- Do not use sensors that have been dropped or have been exposed to other forms of mishandling. Damage to the sensor may have occurred that is not visible.
- Ensure that the sensor is securely mounted.
- Remove cover plate assemblies to access the NOx sensor .
Show/hide table
Illustration 1 g06042664 - Disconnect harness assembly and disconnect sensor cabling (1).
- Use 468-8116 Slotted Socket (22mm) to loosen the sensor.
- Remove inlet NOx sensor probe (2).
Show/hide table
Illustration 2 g06042676 - Install NOx sensor probe. Take precautions to prevent damaging the ceramic sensor element (3) when installing.
Note: During installation, inspection, and handling of the sensor, follow the parameters listed below:
Note: Turn off power supply before disconnecting or connecting the NOx sensor.
- Inspect harness for damaged wiring
- Inspect for secure connections at all ends of the harness
- Do not contact the sensing element when power is applied to the sensor. Contact with the sensing element may result in injury. The sensing element is heated to a minimum of
100° C (212° F) . - Do not use any lubricant on any part of the sensor other than the threads. Do not use unapproved thread lubricant. Do not apply more anti-seize to new parts. If more anti-seize is necessary for pre-installation, use only nickel based anti-seize or non-metallic anti-seize. Apply anti-seize to the threads only and avoid contaminating the sensor head.
- Do not use sensors that have been dropped or have been exposed to other forms of mishandling. Damage to the sensor may have occurred that is not visible.
- Replace the sensor if damaged or faulty.
Caterpillar Information System:
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Sensor Signal (Analog, Active) - Test
C175-20 Locomotive Engine Overhaul (Major)
Exhaust Gas Valve (NRS) for C7.1, C6.6, andC4.4 Engines {1050, 108N} Exhaust Gas Valve (NRS) for C7.1, C6.6, andC4.4 Engines {1050, 108N}
C18 Generator Set Engines Relay (ARD Nozzle Heater) - Remove and Install
C175-20 Locomotive Engine Overhaul (Intermediate)
C175-20 Locomotive Engine Overhaul Considerations
C175-16 Locomotive Engine Configuration Parameters
C175-20 Locomotive Engine Refill Capacities
Cat Gas Engine Lubricant, Fuel, and Coolant Recommendations Hydraulic Oil
Cat Gas Engine Lubricant, Fuel, and Coolant Recommendations Coolant Recommendations
C175-16 and C175-20 Generator Set Engines Fuel Pressure Is Low
Open Crankcase Ventilation System May Experience Freezing on Certain C13, C15, and C18 Generator Set Engines {107F} Open Crankcase Ventilation System May Experience Freezing on Certain C13, C15, and C18 Generator Set Engines {107F}
XQ570 Rental Generator Set Voltage Regulators
XQ570 Rental Generator Set Electronic Modular Control Panel 4 (EMCP 4)
A New Sea Water Pump Is Used on Certain 3608 Marine Auxiliary Engines {1371} A New Sea Water Pump Is Used on Certain 3608 Marine Auxiliary Engines {1371}
G3512 Generator Set Engines Throttle Actuator - Test
C18 Generator Set Engines Diesel Exhaust Fluid Module - Disassemble
New Software Is Used on Certain C7 and C9 Engines {1920} New Software Is Used on Certain C7 and C9 Engines {1920}
Discharge Flange Instructions for Well Stimulation Pumps {5234, 6002} Discharge Flange Instructions for Well Stimulation Pumps {5234, 6002}
C175-20 Locomotive Engine Starting the Engine
C175-16 Locomotive Engine Diesel Exhaust Fluid Nozzle - Inspect/Clean
Technical Analysis 1 (TA1) Visual Inspection for Marine Engine {0372, 1000, 7000, 753S, 7565} Technical Analysis 1 (TA1) Visual Inspection for Marine Engine {0372, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Off-Highway Trucks {0372, 0374, 1000, 7000, 753S, 7565} Technical Analysis 1 (TA1) Visual Inspection for Off-Highway Trucks {0372, 0374, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Paving Compactors {0372, 1000, 7000, 753S, 7565} Technical Analysis 1 (TA1) Visual Inspection for Paving Compactors {0372, 1000, 7000, 753S, 7565}