Cat Data Link - Test
Note: This procedure checks for an open circuit or for a short circuit in the Cat Data Link. If you are experiencing problems with communications between Cat® Electronic Technician (ET) and the Electronic Control Module (ECM), refer to troubleshooting without a diagnostic code Troubleshooting, "Electronic Service Tool Will Not Communicate with ECM" before you use this procedure.
The Cat Data Link is the standard data link that is used by the ECM to communicate with Cat ET. The ECM communicates with Cat ET in order to share status information and diagnostic information. Cat ET can also be used to configure the ECM parameters. This information will not be available if communication fails between the ECM and Cat ET.
Show/hide table
Illustration 1 | g01233970 |
Schematic for the Cat Data Link |
Show/hide table
Illustration 2 | g01167488 |
Typical engine view (1) J1/P1 ECM connectors |
Show/hide table
Illustration 3 | g01149983 |
Typical engine view (2) P61 customer connector (3) P63 service tool connector |
Show/hide table
Illustration 4 | g01202018 |
P1 terminals that are associated with the Cat Data Link (P1-8) Cat Data Link + (P1-9) Cat Data Link − |
Show/hide table
Illustration 5 | g01119122 |
J61 and P61 terminals that are associated with the Cat Data Link (6) Cat Data Link − (7) Cat Data Link + |
Show/hide table
Troubleshooting Test Steps | Values | Results |
1. Inspect the Electrical Connectors and the Wiring A. Remove the electrical power from the ECM. B. Thoroughly inspect connectors (1), (2), and (3). Refer to Troubleshooting, "Electrical Connectors - Inspect". C. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the Cat Data Link. D. Check the allen head screw on each ECM connector for the proper torque. Also, check the allen head screw on the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect", for the correct torque values. |
Electrical Connectors and Wiring |
Results: The harness and the connectors appear to be OK. Proceed to Test Step 2. Results: The connectors and/or the wiring are not OK. Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are coupled. Verify that the original problem is resolved. STOP |
2. Check for a Short Circuit A. Disconnect the J1 connector. B. Disconnect Cat ET from the service tool connector. C. Measure the resistance between the points that are listed in Table 1. Be sure to wiggle the wires in the harnesses as you make each resistance measurement. |
Short Circuit |
Results: Each check of the resistance indicates an open circuit. Proceed to Test Step 3. Results: At least one check of the resistance does not indicate an open circuit. There is a short circuit in the harness or in a connector. Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Verify that the original problem is resolved. STOP |
Show/hide table
Resistance Measurements for the Cat Data Link | |
Connector and Terminal | Terminal |
P1-8 (Cat Data Link +) | All of the other terminals on the P1 connector |
Ground stud | |
P1-9 (Cat Data Link -) | All of the other terminals on the P1 connector |
Ground stud |
Show/hide table
Troubleshooting Test Steps | Values | Results |
3. Check for an Open Circuit A. Fabricate a jumper wire. Use the jumper wire in order to create a short circuit between terminals J63-D (Cat Data Link +) and J63-E (Cat Data Link −). B. Measure the resistance between P1-8 (Cat Data Link +) and P1-9 (Cat Data Link −). |
10 Ohms |
Results: Each check of the resistance is less than ten Ohms. Repair: Perform the following procedure: 1. Connect the J1/P1 connectors. Connect Cat ET to the service tool connector. 2. Check the Cat Data Link for proper operation. If the Data Link does not operate correctly, there may be a problem with the ECM. Temporarily install a new ECM. Check the Cat Data Link again. If the new ECM solves the problem, install the original ECM and verify that the original problem returns. If the new ECM operates correctly and the original ECM does not operate correctly, replace the original ECM. Verify that the problem is resolved. STOP Results: At least one check of the resistance is greater than ten Ohms. There is an open circuit or excessive resistance in the harness. There may be a problem with a connector. Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Verify that the original problem is resolved. STOP |
Caterpillar Information System:
G3520H Generator Set Engine Prelubrication Oil Pump - Remove and Install
2014/12/09 An Improved Refrigerant Compressor Mounting Group Is Used on Certain 3500 Machine Engines {1802}
C7 and C9 Industrial Engines CAN Data Link - Test
3500B Generator Sets Maintenance Interval Schedule - Standby
3516B Generator Set Engines with Dynamic Gas Blending Engine Overcrank Occurrence
3500B Generator Sets Maintenance Interval Schedule - Prime
C3.4B Engines Relay - Test - SCR Relay
794 AC Off-Highway Truck Machine Systems Tire and Rim (Front) - Remove and Install
C3.4B Engines Relay - Test - ECM Main Relay
C3.4B Engines Power Take-Off - Test
C175-16 PETROLEUM ENGINES Fuel Transfer Pump - Remove and Install
2014/09/26 A New Special Instruction Is Now Available for Bypassing EGR Relay in EMCP2 Controls on Certain Generator Sets {1908, 4490, 4493}
C175 Tier 4 Final Engines for Caterpillar Built Machines Alternator - Remove and Install
794 AC Off-Highway Truck Engine Supplement Refrigerant Compressor - Remove and Install
794 AC Off-Highway Truck Engine Supplement Electric Starting Motor - Remove and Install
794 AC Off-Highway Truck Engine Supplement Damper - Remove and Install
794 AC Off-Highway Truck Engine Supplement Belt Tightener - Remove and Install
A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785} A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}
C7 and C9 Industrial Engines Coolant Level - Test
C7 and C9 Industrial Engines Electrical Power Supply - Test
C4.4 Engines for Caterpillar Built Machines Engine Design
G3520H Generator Set Engine Fuel Control Valve - Remove and Install
794 AC Off-Highway Truck Machine Systems Front Wheel, Bearing and Duo-Cone Seal - Remove
794 AC Off-Highway Truck Machine Systems Front Wheel, Bearing and Duo-Cone Seal - Install