Engine Oil Filter Housing - Assemble
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install the O-ring seal on adapter (12).
- Install adapter (12) to bypass valve housing (11). Apply clean unused engine oil to shaft of adapter (12). Using two people, install bypass valve housing (11) to the engine oil filter housing. Install bolts (10) and tighten to a torque of
55 ± 7 N·m (41 ± 5 lb ft) .Show/hide table
Illustration 3 g03702658 - Install bypass valve and spring (9).
Note: The bypass valve must move freely in the bore.
Show/hide table
Illustration 4 g03702656 Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Install the O-ring seals. Install covers (8) and bolts (7).
Show/hide table
Illustration 5 g03702655 - Install the O-ring seal to cover (6). Install cover (6) and nuts (4). Tighten nuts (4) to a torque of
55 ± 7 N·m (41 ± 5 lb ft) . Install sensors (5) and tighten to a torque of10 ± 2 N·m (89 ± 18 lb in) .Show/hide table
Illustration 6 g03702654 - Install new engine oil filter elements (3).
- Install the O-ring seal on cover (2). Lubricate shaft of cover (1) with clean unused engine oil and Install cover (2) and bolts (1).
Show/hide table
| |
| Illustration 1 | g03702697 |
Show/hide table
| |
| Illustration 2 | g03702659 |
End By:
- Install the engine oil filter housing.
Caterpillar Information System:
2014/12/19 New Valve Covers and Seals Are Available for C27 and C32 Engines Installed in Hydraulic Mining Shovels and Rotary Drills {1107, 7555}
XQC1200 and XQC1600 Power Modules Engine Oil Filter Housing - Disassemble
3516C and C175-16 Engines Selective Catalytic Reduction DEF Tank Temperature Is Low
G3500 Engines Maintenance Interval Schedule
TH55-E70 and TH55-E90 Petroleum Transmissions Torque Converter - Disassemble
CX31 On-Highway Transmission Modulating Valve
XQC1200 and XQC1600 Power Modules Engine Oil Filter Housing - Remove and Install
C7.1 Generator Sets Safety Messages
3516C and C175-16 Engines Selective Catalytic Reduction DEF Tank Temperature Is High
C18 Marine Engine Maintenance Interval Schedule
2014/07/25 Water Pump Operation for C7.1 Engines {1361}
3516C and C175-16 Engines Selective Catalytic Reduction DEF Tank Sensor - Test
C8.7 Marine Engine Engine Valve Lash - Check
3516C and C175-16 Engines Selective Catalytic Reduction SCR Warning System Problem
C3.4B Engines Service Tool Features
2014/07/25 New Auxiliary Water Pump and Shaft Seal for Certain 3056 Marine Engines and C1.5, C2.2, C4.4, and C6.6 Generator Sets {1371, 1371, 7555}
G3500 Engines Maintenance Interval Schedule - Standby
G3500 Engines Maintenance Interval Schedule - Turbocharged Aftercooled
2014/07/22 An Improved Valve Cover Seal Is Used on Certain Machine Engines {1107, 7553, 7555}
G3500 Engines Maintenance Interval Schedule - Bio-Gas
G3500 Engines Maintenance Interval Schedule - Naturally Aspirated
2014/07/25 An Improved Valve Cover Seal Is Used on Certain Commercial Engines {1107, 7553, 7555}
330F MHPU Mobile Hydraulic Power Unit Circuit Breakers - Reset
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (DOC Inlet)