Crankshaft Main Bearings - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 2P-5518 | 轴承工具 | 1 |
B | 8T-5096 | 千分表 | 1 |
C | 8T-3052 | 度数轮 | 1 |
开始:
- 拆下发动机机油泵。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查主轴承盖以确认其位置是否正确,并同时检查缸体相关的主轴承盖方向。 主轴承盖必须安装到原来位置并保持原来方向。
Show/hide table
图 1 g00996899 - 将螺栓 (1) 从2 号到 6 号主轴承盖 (2) 上拆下。
注: 当 2 号到 6号主轴承盖安装完毕后拆下 1 号和 7 号主轴承盖 (2)。
Show/hide table图 2 g01020288 - 将工具 (A) 安装到曲轴油孔中。 小心地转动曲轴,以便将主轴承上轴瓦 (3) 从缸体上拆下。
注: 用工具 (A) 从轴承凸舌对侧推主轴承上轴瓦。 如果曲轴转动方向错误,那么就会把轴承上的凸舌推到曲轴和缸体轴承区域之间。 这样会导致缸体和 / 或曲轴的损坏。
Show/hide table图 3 g01134355 - 将止推片 (4) 从 4 号主轴承两侧拆下。
- 从主轴承盖上拆下主轴承的下半部分。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将新的主轴承上轴瓦 (3) 安置在曲轴上。 把上主轴承没有凸舌的一端插入缸体。 将工具 (A) 安装到曲轴油孔中。 小心转动曲轮轴,把主轴承上轴瓦推入缸体。
注: 用工具 (A) 从轴承凸舌一侧推动主轴承上轴瓦。 如果曲轴转动方向错误,那么就会把轴承上的凸舌推到曲轴和缸体轴承区域之间。 这样会导致缸体和 / 或曲轴的损坏。
Show/hide table图 5 g01134355 - 将止推盘 (4) 安装在 4 号主轴承的两侧。
注: 安装止推盘时让标有 "Block Side"(缸体侧)字样的一侧朝向缸体。
- 将曲轴主轴承下轴瓦安装到主轴承盖中。
注: 确保主轴承已经安装完毕,以使轴承凸舌能卡进缸体中的凹槽。
Show/hide table图 6 g01018383 - 将主轴承盖 (2) 装到曲轴上。
注: 确保主轴承盖上的数字和缸体上的数字相符。 同时确保主轴承盖上的 "FRONT"(前)字样要朝向缸体前部。
- 使用清洁的发动机机油润滑螺栓 (1) 的螺纹。 安装螺栓。
- 按照以下步骤拧紧主轴承盖上的螺栓 (1):
- 拧紧螺栓 (A) 至扭矩为
258 ± 14 N·m (190 ± 10 lb ft) 。注: 螺栓 (A) 位于主轴承盖轴承凸舌一侧。
- 拧紧螺栓 (B) 至扭矩为
258 ± 14 N·m (190 ± 10 lb ft) 。注: 螺栓 (B) 位于主轴承盖轴承凸舌的对侧。
- 将螺栓 (B) 再拧紧 120 ± 5 度(2 层丝)。
注: 如果没有使用工具 (C) ,要在螺栓和主轴承盖上作指示标记。
- 将螺栓 (A) 再拧紧 120 ± 5 度(2 层丝)。
注: 如果没有使用工具 (C) ,要在螺栓和主轴承盖上作指示标记。
- 转动曲轴,以便确保曲轴能转动自如。
- 拧紧螺栓 (A) 至扭矩为
- 使用工具 (B) 检查曲轴轴向间隙。 确保工具 (B) 接触的是加工面。 端隙由 4 号主轴承(中心)的止推盘控制。 请参阅技术规格, "曲轴"以了解曲轴轴向间隙。
注: 进行间隙检查之后,安装主轴承并保持其干燥。 请参阅拆解与组装, "轴承间隙 – 检查"。 为了便于最终组装,在主轴承上施加清洁的发动机机油。
注: 确保主轴承已经安装完毕,以便让轴承凸舌卡入缸体中的凹槽。 主轴承上轴瓦有油槽和油孔。
Show/hide table
图 4 | g01020300 |
结束:
- 安装发动机机油泵。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Cylinder Liner - Remove and Install
C175 Commercial Engine Intake Valve Recession {1100} C175 Commercial Engine Intake Valve Recession {1100}
2013/08/06 New Software Is Now Used on Certain C18 Auxiliary and Generator Set Engines {1920}
C15 and C18 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
C18 Generator Set Model View Illustrations
C13 and C15 Generator Sets After Starting Engine
C7.1 Marine Generator Set Welding on Engines with Electronic Controls
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove and Install
C7.1 Marine Generator Set Aftercooler Condensate Drain Valve - Inspect/Clean
C15 and C18 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
C7.1 Marine Generator Set Battery or Battery Cable - Disconnect
C15 and C18 Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Pressure Sensor (DPF) - Remove and Install
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Fuel Lines
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Fuel Lines