Pistons and Connecting Rods - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 6V-6192 | 挡圈钳 | 1 |
B | 7M-3978 | 活塞环扩张器总成 | 1 |
C | 5P-8639 | 液压 (连杆轴承) | 1 |
8F-0024 | 软管组件 | 1 | |
1P-2375 | 连接器 | 1 | |
1P-2376 | 连接器 | 1 | |
5P-8651 | 隔套 | 1 | |
5P-8649 | 适配器 | 1 | |
5P-8650 | 衬套接头 | 1 | |
9U-6600 | 液压泵 | 1 |
注: 从发动机上拆下之前,活塞和连杆组件上已经做了标记。 所有的部件必须重新组装在一起。 所有部件必须安装回它们在发动机中原来的位置。 请勿互换任何部件。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (C) 拆掉旧轴承,同时安装新轴承 (7)。 工具 (C) 的适配器应与连杆 (6) 的表面充分接触。
注: 调整轴承接头两端的方向在位置 (X) ± 5 度范围内。
- 沿长度 (Y) 加热连杆 (6)。
(Y) 加热连杆的最大长度 ...
93 mm (3.7 in) - 让连杆和轴承冷却到室温。
Show/hide table注意 在安装活塞销子轴承的时候,必须对连杆进行加热处理。 不要使用明火加热。
- 沿长度 (Y) 加热连杆 (6)。
- 用销膛磨机加工轴承孔 (7),以修正直径。
轴承孔直径 ...
60.035 ± 0.008 mm (2.36360 ± 0.00030 in) Show/hide table图 3 g01017728 - 将控油环的弹簧放置在活塞体组件中的油环槽中。
- 将控油环 (3) 安置在弹簧的上方。 放置控油环,使其开口与弹簧接头成 180 度。 使用工具 (B) 将控油环安装在活塞上。
- 使用工具 (B) 安装中间活塞环 (2),使有 “UP-2” 标记的一侧朝向活塞顶部。
- 使用工具 (B) 安装顶部活塞环 (1),使有 “UP-1” 标记的一侧朝向活塞顶部。
- 安置活塞环 (1)、 (2) 和 (3),使其开口之间互成120度。
- 检查活塞环 (1)、 (2) 和 (3) 底部之间的间隙。 关于技术规格,请参阅技术规格手册, "活塞和活塞环"。
- 将活塞体组件 (4) 在连杆 (6) 上安置到位。 将清洁的发动机机油涂抹在连杆销 (8) 上,并安装连杆销 (8)。 使用工具 (A) 安装销固定器 (5)。 确保销固定器 (5) 完全落座在活塞体组件 (4) 的槽中,
- 将连杆轴承 (9) 安装在连杆 (6) 和连杆盖 (10) 上。 确保安装连杆轴承 (9) 时轴承凸舌卡入连杆 (6) 和连杆盖 (10) 中的凹槽。
- 确保定位销已安装到连杆盖 (10) 中。
Show/hide table
图 1 | g01018268 |
Show/hide table
图 2 | g01017742 |
结束:
- 安装活塞和连杆。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Cylinder Liner - Remove and Install
C175 Commercial Engine Intake Valve Recession {1100} C175 Commercial Engine Intake Valve Recession {1100}
2013/08/06 New Software Is Now Used on Certain C18 Auxiliary and Generator Set Engines {1920}
C15 and C18 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
C18 Generator Set Model View Illustrations
C13 and C15 Generator Sets After Starting Engine
C7.1 Marine Generator Set Welding on Engines with Electronic Controls
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set System Pressure Release
C15 and C18 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove and Install
C7.1 Marine Generator Set Aftercooler Condensate Drain Valve - Inspect/Clean
C15 and C18 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
C7.1 Marine Generator Set Battery or Battery Cable - Disconnect
C15 and C18 Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Fuel Temperature Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Temperature Sensor (DPF Inlet, Flame Detect) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Pressure Sensor (DPF) - Remove and Install
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines