Auxiliary Water Pump - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 1 |
B | - | Guide Bolt 1/2 - 13 NC by 4 inch |
2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach Tooling (A) and a suitable lifting device to water pump (3). The weight of water pump (3) is approximately
68 kg (150 lb) . - Install a new O-ring seal for the joint between the water pump and the front housing. Apply a light coat of glycerin to the O-ring seal prior to installation.
Show/hide table
Illustration 1 g03078938 - Install Tooling (B) in the front housing.
- Place the water pump (3) on the front housing and slide the water pump (3) into position.
- Install six bolts (2). Tighten bolts to a torque of
60 ± 12 N·m (44 ± 9 lb ft) . Remove Tooling (B) and install remaining bolts (2).Show/hide tableIllustration 2 g03079957 - Install four bolts (1). Tighten bolts to a torque of
47 ± 9 N·m (35 ± 7 lb ft) . - Connect the connection for the water inlet.
- Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Caterpillar Information System:
C280-16 Engine Auxiliary Water Pump - Remove
LC5000, LC6100, and LC7000 Electric Power Generation Rotor - Remove and Install
LC5000, LC6100, and LC7000 Electric Power Generation Terminal Assembly - Remove and Install
LC5000, LC6100, and LC7000 Electric Power Generation Permanent Magnet Pilot Exciter - Remove and Install - PMG
LC5000, LC6100, and LC7000 Electric Power Generation Generator - Remove
LC5000, LC6100, and LC7000 Electric Power Generation Generator - Install
LC5000, LC6100, and LC7000 Electric Power Generation Diode Assembly - Remove and Install
LC5000, LC6100, and LC7000 Electric Power Generation Bearing - Remove and Install
3512C Petroleum Engines with Dynamic Gas Blending Sensor Supply - Test
4-Inch Radial Hose Machine{0374, 0599, 0684, 0738, 5057} 4-Inch Radial Hose Machine{0374, 0599, 0684, 0738, 5057}
3512C Petroleum Engines with Dynamic Gas Blending Emergency Stop - Test
3512C Petroleum Engines with Dynamic Gas Blending Exhaust Temperature Is High
3512C Petroleum Engines with Dynamic Gas Blending Data Link - Test
C280-16 Engine Priority Valve - Install
LC5000, LC6100, and LC7000 Electric Power Generation Exciter Armature - Remove and Install
Rework Procedure for the PAS (Powered Access Stairway) on Certain Off-Highway Trucks{0679, 7253, 7254, 7255} Rework Procedure for the PAS (Powered Access Stairway) on Certain Off-Highway Trucks{0679, 7253, 7254, 7255}
2013/09/27 New Software Is Now Available for All Cat® Products With The Product Link 522 System {7606}
2013/09/20 A Rework Procedure for the Power Access Stairway (PAS) On Certain Off-Highway Trucks is Now Available {7253}
CX31 and CX31 HT On-Highway Transmissions (Cat Truck) Transmission Hydraulic Control
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Engine Oil Pressure Switch
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 126-8022 Generator through 128-7424 Generator
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 136-6580 Generator through 136-6609 Generator
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 141-5534 Generator through 142-9900 Generator
312D2 and 313D2 Excavators System Pressure Release