Auxiliary Water Pump - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
B | 9S-9152 | Bearing Puller Gp | 1 |
C | 1P-0510 | Driver Gp | 1 |
D | 138-9299 | Oil Seal Tool | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean the counterbore for lip type seal (9) in housing assembly (2).
- Use Tooling (C) to install lip type seal (9) in housing assembly (2). Install lip type seal (9) so the face of the seal is flush with Surface (X).
Show/hide table
Illustration 3 g02441278 - Use Tooling (B) and a suitable press to install bearing assembly (7) on shaft (8).
Note: Ensure that the retainer is installed with the Marking "OUTSIDE" towards the gear.
- Install retainer (6). Use Tooling (B) and a suitable press to install gear (4) on shaft (8). Install gear (4) flush against bearing assembly (7).
Show/hide table
Illustration 4 g02441241 - Install Tooling (D) over the shaft. The tapered edge will be facing outward.
- Install the shaft, the bearing assembly, retainer (6), and gear (4) in housing assembly (2). Use care not to damage the lip type seal.
- Remove Tooling (D) from the shaft.
- Install bolts (5).
Show/hide table
Illustration 5 g02442638 - Use hand pressure and the tool that is supplied with seal assembly (10) to install seal assembly (10) on shaft (8). Install seal assembly (10) until the seal assembly is fully seated in the housing assembly.
Show/hide table
Illustration 6 g02440321 - Use a suitable press to install impeller (3) on the shaft. Install impeller (3) flush with the shaft to a depth of
0 - 0.25 mm (0 - 0.010 inch) . - Install O-ring seal (1) on housing assembly (2).
Show/hide table
Illustration 1 | g02442377 |
Show/hide table
Illustration 2 | g02442396 |
End By:
- Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
Caterpillar Information System:
Nitrogen Pressure Test Unit FT2724 {4150, 4159, 4169, 4170, 4171, 4174, 4175, 4180} Nitrogen Pressure Test Unit FT2724 {4150, 4159, 4169, 4170, 4171, 4174, 4175, 4180}
C13, C15, and C18 Tier 4 Interim Engines Data Link - Test
2011/03/02 New Software Is Used on C175-16 Generator Sets {1901, 1920}
C15 Petroleum Engines Auxiliary Water Pump - Disassemble
793F Off-Highway Truck Machine Systems Valve (Suspension Cylinder Charging) - Remove and Install - Front Suspension Cylinder
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Transfer Operation
C15 Petroleum Engines Auxiliary Water Pump - Install
C15 Petroleum Engines Auxiliary Water Pump - Remove
Installation Procedure of International Protection Rating (IP32) for the UPSB505{4480} Installation Procedure of International Protection Rating (IP32) for the UPSB505{4480}
CX31 and CX31 HT On-Highway Transmissions Reference Material
CX31 and CX31 HT On-Highway Transmissions Transmission Oil Sample - Obtain
CX31 and CX31 HT On-Highway Transmissions Transmission Oil Level - Check
UPSB505 Uninterruptible Power Supply Cable Size Requirement
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Electrical Connections
2011/06/16 New Fuel Pressure Regulators Are Used on Certain C7 and C9 Engines {1715}
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Initial Startup Procedure
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Pager Configuration
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Interfaces
C15 Petroleum Engines Aftercooler - Remove
C15 Petroleum Engines Aftercooler - Install
C15 Petroleum Engines Installation Environment
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Remote Status Panel
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Site Preparation
UPSB505 Uninterruptible Power Supply System Earthing Arrangement