Fuel Filter Base - Remove and Install - Primary
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 185-3630 | Strap Wrench As | 1 |
- Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
- Disconnect the harness assembly (not shown).
Show/hide table
Illustration 1 g02175143 - Drain the primary filter and use Tooling (A) in order to remove the primary filter (1). Refer to Operation and Maintenance Manual, "Fuel System Primary Filter (Water Separator) Element - Replace".
Show/hide table
Illustration 2 g02175165 - Remove check valve (2). Remove backup ring (3), O-ring seals (4) and (5).
Show/hide table
Illustration 3 g02175476 - Remove nut (6) and remove coil (7).
- Remove cartridge (8). Remove backup ring (11), and remove O-ring seals (9) and (10).
Show/hide table
Illustration 4 g02175494 Show/hide tablePersonal injury can result from being struck by parts propelled by a released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to release the spring force.
- Remove plug (15) and remove the O-ring seal. Remove spring (14), valve (12) and O-ring seal (13). Repeat this step for the other check valve assembly.
- Remove the Fuel Priming Pump. Refer to Disassembly and Assembly Manual, "Fuel Priming Pump - Remove and Install".
- Install the fuel filter and the fuel filter base in the reverse order.
- Tighten plug (15) to a torque of
95 ± 10 N·m (70 ± 7 lb ft) . - Tighten check valve (2) to a torque of
28 ± 3 N·m (21 ± 2 lb ft) . - Tighten cartridge (8) to a torque of
28 ± 3 N·m (21 ± 2 lb ft) . - Tighten nut (6) to a torque of
6.5 ± 0.5 N·m (58 ± 4 lb in) .
- Tighten plug (15) to a torque of
Show/hide table
NOTICE |
---|
Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary. |
Caterpillar Information System:
349F and 352F Excavators Machine System Swing Drive
Capturing Photo, Video, or Audio Evidence of Machine Issues{0336, 1000, 7000} Capturing Photo, Video, or Audio Evidence of Machine Issues{0336, 1000, 7000}
G3512 Generator Set Engines Excessive Engine Oil Consumption - Inspect
C7.1 Industrial Engine and Generator Set Diesel Particulate Filter Has Low Inlet Pressure
C27 and C32 Tier 4 Engines Air Inlet and Exhaust Lines
362-4250 Deck Height Measuring Tool{1201} 362-4250 Deck Height Measuring Tool{1201}
C18 Generator Set Generator - Install
C18 Generator Set Generator - Remove
C27 and C32 Tier 4 Engines Exhaust Diffuser Adapter
C27 Generator Set Engines Inlet Air Temperature Sensor
C4.4 Industrial Engine Customer Assistance
320E and 323E Excavators Engine Oil Sample - Obtain
C27 Generator Set Engines Sensor Signal (Analog, Active) - Test
C27 and C32 Tier 4 Engines Exhaust Manifold
C27 Generator Set Engines Sensor Signal (Analog, Passive) - Test
349F and 352F Excavators Machine System Bypass Valve (Return) - Bypass Check Valve
C27 and C32 Tier 4 Engines Air Shutoff
349F and 352F Excavators Hydraulic System Hydraulic Tank and Filter
242-3567 Variable Crimp Die Bowl{0684} 242-3567 Variable Crimp Die Bowl{0684}
C27 Generator Set Engines Sensor Supply - Test
C27 and C32 Tier 4 Engines Flywheel Housing
2011/02/10 New Valve Stem Seals Are Available for Certain C13 and C15 On-Highway Engines {1100, 7555}
349F and 352F Excavators Hydraulic System Hydraulic Oil Cooler
349F and 352F Excavators Machine System Oil Filter (Return) - Case Drain Filter