Valve Mechanism Cover - Remove and Install
Start By:
- Remove the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Remove and Install".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bracket (4).
- Remove bolts (1) and clips (2).
- Remove valve mechanism cover (3) and the seal.
Show/hide table
| |
| Illustration 1 | g01479054 |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 230-6262 | Sealant | - |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply Tooling (A) to the overlapping area on the seal. Position the seal and valve mechanism cover (3) on the engine.
- Install clips (2) and bolts (1). Tighten bolts (1) in a numerical sequence to a torque of
20 ± 3 N·m (15 ± 2 lb ft) . - Install bracket (4).
Show/hide table
|
| |
| Illustration 2 | g01479054 |
Show/hide table
| |
| Illustration 3 | g01479055 |
End By:
- Install the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Remove and Install".
Caterpillar Information System:
Transmission Clutch Plates and Disc Assemblies with Rayflex Friction Material {3030, 3155, 3190} Transmission Clutch Plates and Disc Assemblies with Rayflex Friction Material {3030, 3155, 3190}
2008/03/17 Updated Instruction For The Bypass Harness {0785, 1408}
2008/04/14 Increased Support for Repair Parts is Available for Products that are sold by Dealer Service Tools from Advanced Technology Services {0599}
C7 PETROLEUM Petroleum Engine Housing (Front) - Install
C7 PETROLEUM Petroleum Engine Housing (Front) - Remove
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C4.4 and C6.6 Engines for Caterpillar Built Machines Electrical Connectors - Inspect
2008/03/17 A New Bearing Block within the Governor is Now Used {1000}
C7 PETROLEUM Petroleum Engine Crankshaft Rear Seal - Install
C7 PETROLEUM Petroleum Engine Water Temperature Regulator - Remove and Install
C175-16 and C175-20 Generator Set Engines Cylinder Head Valves
Information on the Clean Gas Induction (CGI) Flex Pipe Connection Found Broken in Some 2007 Emissions Compliant Engines{1071, 108N, 5510} Information on the Clean Gas Induction (CGI) Flex Pipe Connection Found Broken in Some 2007 Emissions Compliant Engines{1071, 108N, 5510}
345D, 349D and 349D2 Excavator Machine System Specifications Main Hydraulic Pump Mounting
3516C Locomotive Engine Configuration Parameters
C175-16 and C175-20 Generator Set Engines Air Lines
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Pilot Lines - Joystick
3516C Locomotive Engine Maintenance Interval Schedule
C175-16 and C175-20 Generator Set Engines Air Lines
C32 Marine Engine Refill Capacities and Recommendations
Procedure to Install a Service Kit for the Unloader for the Air Compressor{1803} Procedure to Install a Service Kit for the Unloader for the Air Compressor{1803}
Some 3500 Cylinder Packs May Have Incorrect Pistons{1225} Some 3500 Cylinder Packs May Have Incorrect Pistons{1225}
345D, 349D and 349D2 Excavator Machine System Specifications Pilot Lines - Control Valve
Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290} Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290}