Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 2P-5518 | Bearing Tool | 1 |
B | 8T-5096 | Dial Indicator | 1 |
C | 8T-3052 | Degree Wheel | 1 |
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position new upper main bearing (5) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to push the upper main bearing into the cylinder block.
Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
- Install the thrust plates on each side of the No. 4 main bearing.
Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
- Install the lower halves of the crankshaft main bearings in the main bearing caps.
Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.
Show/hide tableIllustration 2 g01367531 - Position main bearing caps (2) on the crankshaft.
Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
- Lubricate the threads of bolts (1) and bolts (3) with clean engine oil. Install the bolts.
- Tighten bolts (1) and bolts (3) for the main bearing caps, as follows:
- Tighten Bolt (A) to a torque of
258 ± 14 N·m (190 ± 10 lb ft) .Note: Bolt (A) is on the bearing tab side of the main bearing cap.
- Tighten Bolt (B) to a torque of
258 ± 14 N·m (190 ± 10 lb ft) .Note: Bolt (B) is on the opposite side of the bearing tab of the main bearing cap.
- Tighten Bolt (B) for an additional 120 ± 5 degrees (2 flats).
Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
- Tighten Bolt (A) for an additional 120 ± 5 degrees (2 flats).
Note: If Tooling (C) is not used, place an index mark on the bolt and the main bearing cap.
- Tighten Bolt (D) to a torque of
80 ± 10 N·m (59 ± 7 lb ft) .Note: Bolt (D) is on the opposite side of the bearing tab of the main bearing cap.
- Tighten Bolt (C) to a torque of
80 ± 10 N·m (59 ± 7 lb ft) .Note: Bolt (C) is on the bearing tab side of the main bearing cap.
- Rotate the crankshaft in order to ensure that the crankshaft turns freely.
- Tighten Bolt (A) to a torque of
- Use Tooling (B) to check the crankshaft end play. Ensure that Tooling (B) is against a machined surface. The end play is controlled by the thrust plates of No. 4 main bearing (center).
Crankshaft end play (new thrust plates) ...
0.10 to 0.60 mm (0.004 to 0.024 inch) Note: Ensure that the correct hardware is used to install side covers (4). Ensure that side covers (4) are installed securely.
- Install four side covers (4).
Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.
Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 1 | g01367507 |
End By:
- Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".