Power Train Guard (Transmission) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-7505 | Hydraulic Jack | 1 |
- | Steel Plate approximately |
1 |
Show/hide table
(1) | Tack weld the steel plate to the top plate of the hydraulic jack. |
Start By:
- Connect the steering frame lock.
- Release the hydraulic system pressure.
- Remove panel (1).
Show/hide table
Illustration 2 g03677892 - Disconnect hose assembly (2).
- Remove the cotter pin and pin (3).
Show/hide table
Illustration 3 g03677911 - Disconnect hose assembly (5).
- Cut cable strap (7).
- Remove the cotter pin, pin (4), and guard cylinder (6).
Show/hide table
Illustration 4 g03677927 Note: Power train guard (10) may contain a significant amount of rock, dirt, liquids, and debris, which will result in significant additional weight.
- Position Tooling (A) and suitable cribbing under power train guard (10). Raise Tooling (A) until Tooling (A) and the suitable cribbing contacts power train guard (10). The weight of power train guard (10) is approximately
330 kg (728 lb) . - Remove three bolts (8) (not shown) and the washers. Remove bolts (9) and the washers. Repeat this step for the opposite side.
Show/hide table
Do not lower the bottom guard while under the machine. Injury could occur if the bottom guard slips off of the jack while it is being lowered.
- Use Tooling (A) in order to carefully lower power train guard (10).
Show/hide table
Illustration 1 | g03677808 |
- Install power train guard (10) in the reverse order of removal.
Caterpillar Information System:
525D, 535D, 545D and 555D Wheel Skidders Information Display Diagnostic Trouble Codes
525D, 535D, 545D and 555D Wheel Skidders Information Display Determining Diagnostic Trouble Codes
525D, 535D, 545D and 555D Wheel Skidders Information Display Diagnostic Capabilities
C13, C15, and C18 Tier 4 Final Engines Turbocharger
525D, 535D, 545D and 555D Wheel Skidders Information Display Service Tools
525D, 535D, 545D and 555D Wheel Skidders Information Display General Information
D6T Track-Type Tractor Systems Idlers (Track)
C4.4 Engines for Caterpillar Built Machines Pressure Sensor (NOx Reduction System) - Differential Pressure Sensor
C4.4 Engines for Caterpillar Built Machines Pressure Sensor (NOx Reduction System)
D6 Track Type Tractor Machine Systems Idlers (Track)
990K Wheel Loader Systems Differential
990K Wheel Loader Systems Differential
525D, 535D, 545D and 555D Wheel Skidders Information Display Alarm - Test
525D, 535D, 545D and 555D Wheel Skidders Information Display CAN Data Link - Test
525D, 535D, 545D and 555D Wheel Skidders Information Display Charging System - Test
525D, 535D, 545D and 555D Wheel Skidders Information Display Electrical Connector - Inspect
525D, 535D, 545D and 555D Wheel Skidders Information Display Wiring Harness (Open Circuit) - Test
525D, 535D, 545D and 555D Wheel Skidders Information Display Wiring Harness (Short Circuit) - Test
844K Wheel Dozer Machine Systems Pilot Control Actuator Current (Proportional Solenoid) - Check
525D, 535D, 545D and 555D Wheel Skidders Information Display Module - Replace
525D, 535D, 545D and 555D Wheel Skidders Information Display Module - Flash Program
525D, 535D, 545D and 555D Wheel Skidders Information Display Connector Contact Description
844K Wheel Dozer Machine Systems Tilt Control Valve (Dual) - Check
D6T Track Type Tractor Machine Systems Cutting Edges and End Bits