Pistons and Connecting Rods - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 9S-9082     | 发动机盘车工具     | 1     |
开始:
- 拆下缸盖。
- 拆下发动机机油泵。
- 拆下活塞冷却喷嘴。
- 从缸套内表面顶部开始清除积碳凸起。
- 使用工具 (A) 转动曲轴,直到两个活塞处于底部中心。
- 安装螺栓 (1) 和轴承盖。 推动连杆和活塞,直到活塞环处于缸套外。
注: 拆卸活塞和连杆时,当心不要损坏缸套和/或曲轴轴颈。
Show/hide table
图 1 | g01032888 |
- 从缸套上拆下活塞 (2) 和连杆。
Show/hide table
图 2 | g01032895 |
- 重复步骤 1 至 4,以拆下其余的活塞和连杆。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
B     | 5P-3526 或 149-7180     |
活塞环压缩器     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将清洁的发动机机油涂抹在缸套孔、活塞环,以及活塞外表面上。
Show/hide table
图 3 | g01032680 |
- 使用工具 (B) 将活塞 (2) 和连杆装进缸套。
注: 活塞和连杆安装中,当心不要损坏缸套和/或曲轴轴颈。
- 将连杆和活塞安装到发动机中时,必须使表面 (X) 面向曲轴主轴承轴颈。 表面 (Y) 必须面向连杆。
注: 表面 (X) 比表面 (Y) 厚。
注: 表面 (X) 上加工有倒角,以便于装配曲轴。
Show/hide table
图 4 | g01096077 |
8 缸和 12 缸发动机的典型示例 |
- 确保活塞冠、活塞裙和活塞杆正确对齐,以获得机油喷管 (3) 所需的间隙。 这样可防止主要发动机故障。 请参阅技术参数, "连杆"和技术参数, "活塞和活塞环"。
注: 连杆上的标记需要面向冷却喷嘴侧。
- 安装螺栓 (1) 和轴承盖。 关于正确的上紧程序,请参阅技术参数, "连杆"。
Show/hide table
图 5 | g01032888 |
End By:
- 安装活塞冷却喷嘴。
- 安装发动机机油泵。
- 安装缸盖。
Caterpillar Information System:
854K Wheel Dozer and 992K Wheel Loader Machine Systems Manifold Group (Pilot) - Disassemble
950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 3654 - FMI 02
854K Wheel Dozer, and 992K and 993K Wheel Loaders Monitoring System MID 052 - CID 0168 - FMI 04
854K Wheel Dozer, and 992K and 993K Wheel Loaders Monitoring System MID 052 - CID 0168 - FMI 03
D9R Track-Type Tractor Hydraulic System Oil Level - Check
950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 3654 - FMI 08
992K Wheel Loader and 854K Wheel Dozer Braking System Parking Brake Control
950K Wheel Loader and 962K Wheel Loader Steering System Relief Valve (Steering Cylinder Crossover) - Test and Adjust
854K Wheel Dozer and 992K Wheel Loader Machine Systems Manifold Group (Pilot) - Remove and Install
CG137-08 and CG137-12 Engines Timing Gears - Remove and Install
CG137-08 and CG137-12 Engines Timing Gear Cover - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Power Train Wheel Bearings - Adjust
950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 0364 - FMI 13
950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 0769 - FMI 13
CG137-08 and CG137-12 Engines Cylinder Liner - Remove and Install
950K Wheel Loader and 962K Wheel Loader Steering System Steering Pilot System Pressure - Test - Command Control Steering
CG137-08 and CG137-12 Engines Camshaft - Remove and Install
950K and 962K Wheel Loaders Electrohydraulic System MID 082 - CID 3654 - FMI 13
992K Wheel Loader Electrohydraulic System MID 082 - CID 0041 - FMI 04
CG137-08 and CG137-12 Engines Camshaft Bearings - Remove and Install
D9R Track-Type Tractor Hydraulic System Oil - Change
CG137-08 and CG137-12 Engines Crankshaft Main Bearings - Remove and Install
950K Wheel Loader and 962K Wheel Loader Steering System Pilot Valve (Command Control Steering) Supply Pressure - Test and Adjust
D11T Track-Type Tractor Engine Supplement Engine and Torque Divider - Install