Fuel Priming Pump
Specifications
Show/hide table
Illustration 1 | g02337737 |
Show/hide table
SPECIFICATIONS FOR 359-5530 Manifold     | |||
Callout     | Part Number     | Part Name     | Specification Description     |
3     | 6V-8359     | Bolt     | Torque to......................... 12 ± 3 N·m (106 ± 27 lb in)     |
6     | 6D-5801     | Locknut     | ·Write down the polarity and remove the wires (6) from the terminal studs. The polarity is designated by "+" and "-" signs around the terminal studs. ·Torque to new locknut.... 1.3 N·m (11.5 lb in)     |
-     | -     | -     | After reassembly, prime the engine by turning on the key or pressing the manual switch. The manual switch, if available, is located on the primary fuel filter base. Visually check for leaks around the pump and around the connections on the ARD manifold. If leaks are observed, resolve the leak issue before proceeding further.     |
Removal Procedure
Start By:
- Remove the left side access door and covers.
- Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
- Remove fuel line (1) .
Show/hide table
Illustration 2 | g02337618 |
- Disconnect harness assembly (2). Remove bolts (3) and remove manifold (4) .
- Remove two locknuts (5) .
Show/hide table
Illustration 3 | g02138698 |
- Write down the polarity and remove the wires (6) from the terminal studs. The polarity is designated by "+" and "-" signs around the terminal studs.
Show/hide table
Illustration 4 | g02139150 |
- Remove seal (7) .
Show/hide table
Illustration 5 | g02139164 |
- Remove pump assembly (8).
Show/hide table
Illustration 6 | g02139169 |
- Remove two backup rings (9), seal (10), and seal (11) from the pump assembly.
Show/hide table
Illustration 7 | g02167735 |
Installation Procedure
- Use the pump seal installer that is provided in the pump kit to press in new pump (12) and seals.
Note: The outlet of the pump should be at the top center position.
Show/hide table
Illustration 8 | g02139275 |
Proper orientation of the new fuel priming pump. |
- Install the wires on the terminal studs. Install new locknuts (6). Torque locknuts to 1.3 N·m (11.5 lb in).
Show/hide table
Illustration 9 | g02139286 |
- Install new seal (7) .
Show/hide table
Illustration 10 | g02139307 |
- Install the manifold (4) .
Show/hide table
Illustration 11 | g02139309 |
- Reinstall bolts (3). Torque the bolts to 12 ± 3 N·m (106 ± 27 lb in).
Show/hide table
Illustration 12 | g02139311 |
- Replace filter connector fitting (13) .
Show/hide table
Illustration 13 | g02138801 |
- Reconnect the solenoid harness (2) .
Show/hide table
Illustration 14 | g02139316 |
- Turn the fuel supply to the ON position and turn the power disconnect switch to the ON.
- Use two people in order to flush the fuel pump and fuel line (1) into a suitable container for disposal. The fuel pump can be activated by turning on the key or pressing the manual switch. The manual switch, if available, is located on the primary fuel filter base.
- Connect fuel line (1) to the ARD manifold.
- After reassembly, prime the engine by turning on the key or pressing the manual switch. The manual switch, if available, is located on the primary fuel filter base. Visually check for leaks around the pump and around the connections on the ARD manifold. If leaks are observed, resolve the leak issue before proceeding further.
Caterpillar Information System:
D6T Track-Type Tractor Machine Systems including Specifications Joystick Control (VPAT)
D6T Track-Type Tractor Machine Systems including Specifications Joystick Control (Std Blade)
D6T Track-Type Tractor Machine Systems including Specifications Joystick Control (AccuGrade, VPAT)
D6T Track-Type Tractor Engine including Specifications Engine Oil Pump
D6T Track-Type Tractor Machine Systems including Specifications Joystick Control (Rear Hydraulics)
D6T Track-Type Tractor Engine including Specifications Engine Control Module
D6T Track-Type Tractor Power Train System Pressure - Release
C3.4B Engines for Caterpillar Built Machines Air Inlet and Exhaust System
621H Wheel Tractor-Scraper Lubricant Viscosities
992K Wheel Loader Machine Systems Piston Pump (Brake) - Remove and Install
627H Wheel Tractor-Scraper Monitoring System
D6T Track-Type Tractor Engine including Specifications Oil Cooler (Power Train)
D6T Track-Type Tractor Engine including Specifications Fuel Manifold (Rail)
D6T Track-Type Tractor Engine including Specifications Relief Valve (Fuel)
D6T Track-Type Tractor Machine Systems including Specifications Valve Mounting
992K Wheel Loader Machine Systems Brake Accumulator - Install
992K Wheel Loader Machine Systems Brake Accumulator - Remove
D6T Track-Type Tractor Machine Systems including Specifications Case and Frame
D6T Track-Type Tractor Machine Systems including Specifications Drawbar
D6T Track-Type Tractor Machine Systems including Specifications Counterweight Group
D6T Track-Type Tractor Machine Systems including Specifications Fender
D6T Track-Type Tractor Engine including Specifications Relay (ARD Nozzle Heater) - Clean Emissions Module
D6T Track-Type Tractor Machine Systems including Specifications Platform
D6T Track-Type Tractor Machine Systems including Specifications Striker Bar