Drive Shaft (Front) and Drive Shaft Support Bearing - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 1     |
B     | 1U-7505     | 液压千斤顶     | 1     |
C     | FT-1114     | 真空舱     | 1     |
5P-0306 | 真空传感器     | 1     | |
6V-4142 | 接头     | 1     | |
5K-5068 | 接头     | 1     | |
D     | 1U-9200     | 操纵杆滚轮起重机     | 1     |
e     | 154-6182     | M12 x 1.75,长 150 mm 顶出螺栓     |
2     |
F     | 1P-0520     | 冲头总成     | 1     |
ZZ     | 6V-9509     | 插头     | 1     |
6V-9830 | 盖组件     | 1     |
开始:
- 卸下中心驱动轴。 请参阅拆解和组装, "驱动轴(中心) - 拆卸和安装"。
注: 维修数据:拆卸和安装中的工具 (ZZ) 将不在图示中列出。 显示这一工具是为了协助有经验的维修人员。
- 将工具 (A) 和适当的起吊设备连接到防护罩组件 (1) 上。 将工具 (B) 安置在防护罩组件 (1) 的下面。 防护罩组件 (1) 的重量约为 41 kg (90 lb)。 拆下螺栓 (2) 并将防护罩组件 (1) 降至地面。
Show/hide table
图 1 | g01135669 |
- 将工具 (C) 连接到液压油箱 (3) 上。
Show/hide table
图 2 | g01135686 |
- 断开软管组件 (4) 。
注: 必须断开软管组件 (4) 留出正确的间隙,用于在下一步安装工具。
Show/hide table
图 3 | g01135692 |
- 将工具 (A) 固定到主液压控制阀 (5) 的侧面。 将工具 (D) 连接到工具 (A) 上。 将工具 (D) 和适当的起吊设备固定到前驱动轴 (6) 上。 前驱动轴 (6) 的重量约为 61 kg (135 lb)。
Show/hide table
图 4 | g01135696 |
Show/hide table
图 5 | g01135712 |
- 从前驱动轴 (6) 上卸下螺栓 (7) 。
- 卸下螺栓 (8) 和护圈 (9) 。
Show/hide table
图 6 | g01135733 |
- 拆下 O 形密封圈 (10) 和轭组件 (11) 。
Show/hide table
图 7 | g01135739 |
- 卸下螺栓 (12) 和轴承保持架 (13) 。
Show/hide table
图 8 | g01135744 |
- 从轴承保持架 (13) 上卸下唇形密封 (14) 。
Show/hide table
图 9 | g01135757 |
- 拆下 O 形密封圈 (15) 。
Show/hide table
图 10 | g01135752 |
- 安装工具 (E) ,然后拆下轴承保持架 (16) 。
Show/hide table
图 11 | g01135763 |
- 使用工具 (F) 和适当的起吊设备从轴承保持架 (16) 拆卸滚柱轴承 (17) (未显示)和滚柱轴承 (18) (未显示)。 从轴承保持架 (16) 上卸下唇形密封。
Show/hide table
图 12 | g01135766 |
- 将前驱动轴 (6) 降至地面。
Show/hide table
图 13 | g01135777 |
Caterpillar Information System:
994F Wheel Loader Steering System Monitoring System (Steering Functions)
3500B Marine Propulsion Engines Auxiliary Water Pump - Inspect
988H Wheel Loader C18 Engine Supplement Hood and Engine Enclosure - Install
3306B Industrial Engine Emergency Stopping
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Install
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Remove
525C, 535C and 545C Wheel Skidders Transmission Oil Level - Check
994F Wheel Loader Steering System Oil Filter (Steering Cooler Screen) (Brake Cooler Screen)
994F Wheel Loader Hydraulic System Oil Level (Brake Cooling) - Check
3516B and 3516B HD Engines and 994D, 994F, and 994H Wheel Loaders Fuel System Operation
994F Wheel Loader Hydraulic System Oil Level (Implement) - Check
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Factory Passwords
3406E, C12, C15 and C18 Marine Engines CID 0096 FMI 03 Fuel Level Sensor open/short to +batt
3406E, C12, C15 and C18 Marine Engines CID 0096 FMI 04 Fuel Level Sensor short to ground
C11 and C13 Engines for Caterpillar Built Machines Electronic Unit Injector - Remove
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Fuel Filter Base - Electric Fuel Priming Pump
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Disassemble
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Assemble
994F Wheel Loader Hydraulic System Oil (Brake Cooling) - Change
994F Wheel Loader Hydraulic System Oil Filter (Implement Pump Case Drain) - Replace
994F Wheel Loader Hydraulic System Oil Filter (Steering Cooler Screen) (Brake Cooler Screen) - Clean
AD45B Underground Articulated Truck Engine Air Filter Primary Element - Clean/Replace
C11 and C13 Engines for Caterpillar Built Machines Electronic Unit Injector - Install
3500B Marine Propulsion Engines Sea Water Strainer - Clean/Inspect