Hood and Engine Enclosure - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7573     | 连杆支架     | 1     |
- 安装薄板组件 (34) 后安装螺栓 (33) 。
Show/hide table
图 1 | g01135566 |
- 将工具 (A) 和合适的起吊设备连接到支撑组件 (31) 。 安装支撑组件 (31) 后安装螺栓 (32) 。 支撑组件 (31) 的重量约为 80 kg (175 lb)。
Show/hide table
图 2 | g01135558 |
Show/hide table
图 3 | g01135535 |
- 将螺栓 (29) 和 (30) 安装到支撑组件 (31) 上。 对机器的另一侧重复以上操作。
- 安装托架组件 (28) 和螺栓 (27) 。
Show/hide table
图 4 | g01135519 |
Show/hide table
图 5 | g01135523 |
- 关闭检修门 (26) 。
Show/hide table
图 6 | g01135516 |
- 连接线束组件 (25) 。
Show/hide table
图 7 | g01135513 |
- 安装侧面板 (23) 和 (24) 。
Show/hide table
图 8 | g01135474 |
- 将适当的起吊设备固定到立柱组件 (19) 上。 作为一体安装立柱组件 (19) 和检修门 (21) 。 立柱组件 (19) 和检修门 (21) 的重量约为 34 kg (75 lb)。 安装螺栓 (22) 。 将软管组件 (20) 连接到用来固定空气滤清器维修指示器的立柱组件 (19) 上。
Show/hide table
图 9 | g01135453 |
Show/hide table
图 10 | g01135475 |
- 将适当的起吊设备固定到立柱组件 (16) 上。 作为一体安装立柱组件 (16) 和检修门 (17) 。 立柱组件 (16) 和检修门 (17) 的重量约为 32 kg (70 lb)。 安装螺栓 (18) 。
Show/hide table
图 11 | g01135431 |
Show/hide table
图 12 | g01135437 |
- 连接软管组件 (14) 。 将线束组件 (15) 连接到辅助起动乙醚罐 (13) 和立柱组件 (16) 上。
- 将软管 (8) 滑入位置 (9) 后上紧卡箍 (10) 。 安装护罩组件 (12) 后安装螺栓 (11) 。 对另一侧重复上述步骤。
Show/hide table
图 13 | g01135427 |
- 安装格栅 (6) 后安装螺栓 (7) 。
Show/hide table
图 14 | g01135421 |
- 安装夹子 (4) ,然后安装螺栓 (5) 。
Show/hide table
图 15 | g01135418 |
- 将轨道 (2) 滑到机器的右侧。 安装螺栓 (1) 和 (3) 。
Show/hide table
图 16 | g01135415 |
- 加注冷却系统。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
- 将蓄电池断路开关转到接通位置。
End By: 安装消音器。 请参阅 拆解和组装, "消音器 - 拆卸和安装"。
Caterpillar Information System:
3306B Industrial Engine Emergency Stopping
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Install
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Remove
525C, 535C and 545C Wheel Skidders Transmission Oil Level - Check
994F Wheel Loader Steering System Oil Filter (Steering Cooler Screen) (Brake Cooler Screen)
994F Wheel Loader Hydraulic System Oil Level (Brake Cooling) - Check
3516B and 3516B HD Engines and 994D, 994F, and 994H Wheel Loaders Fuel System Operation
994F Wheel Loader Hydraulic System Oil Level (Implement) - Check
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Factory Passwords
C11 and C13 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
994F Wheel Loader Hydraulic System Oil Filter (Steering Pump Case Drain) - Replace
973D Track-Type Loader Cooling System Water Temperature Regulator - Clean/Replace
3500B Marine Propulsion Engines Auxiliary Water Pump - Inspect
994F Wheel Loader Steering System Monitoring System (Steering Functions)
988H and 988K Wheel Loaders Power Train Drive Shaft (Front) and Drive Shaft Support Bearing - Remove
3406E, C12, C15 and C18 Marine Engines CID 0096 FMI 03 Fuel Level Sensor open/short to +batt
3406E, C12, C15 and C18 Marine Engines CID 0096 FMI 04 Fuel Level Sensor short to ground
C11 and C13 Engines for Caterpillar Built Machines Electronic Unit Injector - Remove
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Fuel Filter Base - Electric Fuel Priming Pump
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Disassemble
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Assemble
994F Wheel Loader Hydraulic System Oil (Brake Cooling) - Change
994F Wheel Loader Hydraulic System Oil Filter (Implement Pump Case Drain) - Replace
994F Wheel Loader Hydraulic System Oil Filter (Steering Cooler Screen) (Brake Cooler Screen) - Clean