Bevel and Transfer Gears - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | -     | 顶出螺栓 1/2 in X 13 X 4 in     |
3     |
B     | 138-7575     | 连杆支架     | 2     |
C     | 5P-2187     | 提升支架     | 1     |
D     | 129-3253     | 扳手套筒     | 1     |
E     | 1P-1863     | 挡圈钳     | 1     |
H     | 138-7576     | 连杆支架     | 2     |
J     | 6V-6080     | 扭矩倍增器总成     | 1     |
K     | 6V-6042     | 千分表触针总成     | 1     |
8T-5096 | 千分表总成     | 1     | |
L     | 1P-0520     | 冲头总成     | 1     |
M     | -     | 顶出螺钉 5/8 in X 11 X 4 in     |
1     |
N     | 132-8112     | 扭矩扳手总成     | 1     |
132-8223 | 液压泵和马达总成     | 1     | |
P     | 7M-7456     | 轴承安装固定胶     | 1     |
Q     | 5P-3931     | 防咬合剂     | 1     |
R     | 155-0695     | 螺纹锁固胶     | 1     |
- 安装接头 (50) 和管组件 (51) 。
Show/hide table
图 1 | g01102661 |
- 如图所示,重新将伞齿轮和分动器齿轮壳体 (2) 放置到位。 冷却轴承外圈 (52) 。 安装轴承外圈 (52) 。 安装板 (27) 和新螺栓 (28) 。
Show/hide table
图 2 | g01101346 |
- 安装齿轮 (26) 。 加热轴承内圈 (25) 。 安装轴承内圈 (25) 。
Show/hide table
图 3 | g01089933 |
- 加热轴承内圈 (24) 。 安装轴承内圈 (24) 。
Show/hide table
图 4 | g01089930 |
- 将工具 (A) 和适当的起吊设备连接到小齿轮组件 (23) 上。 小齿轮组件 (23) 的重量约为 84 kg (185 lb)。 安装小齿轮组件 (23) 。
Show/hide table
图 5 | g01089924 |
- 加热轴承内圈 (20) 。 安装轴承内圈 (20) 。
Show/hide table
图 6 | g01101529 |
- 加热轴承内圈 (19) 。 安装轴承内圈 (19) 。
Show/hide table
图 7 | g01089916 |
- 将工具 (C) 和适当的起吊设备连接到齿轮组件 (18) 上。 齿轮组件 (18) 的重量约为 45 kg (100 lb)。 安装齿轮组件 (18) 。
Show/hide table
图 8 | g01089907 |
- 不要让工具 (C) 挂住齿轮组件 (18) 下方的管组件。 拆下工具 (C) 。
Show/hide table
图 9 | g01089890 |
- 将工具 (B) 和适当的起吊设备安装到板 (17) 上。 板 (17) 的重量约为 57 kg (125 lb)。 安装板 (17) 。
Show/hide table
图 10 | g01101533 |
- 将工具 (R) 涂覆到新螺栓 (13) 上。 安装所有长度相同的新螺栓 (13) 。 拧紧螺栓 (13) 至扭矩为 270 ± 40 N·m (199 ± 30 lb ft)。
Show/hide table
图 11 | g01101535 |
- 冷却轴承外圈 (11) 。 安装轴承外圈 (11) 。
Show/hide table
图 12 | g01089851 |
- 安装原有的垫片 (10) 。 安装保持架 (9) 。 安装新螺栓 (8) 。 拧紧螺栓 (8) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。 使用工具 (K) 检查轴向间隙。 轴向间隙应为 0.08 ± 0.03 mm (0.003 ± 0.001 in)。 调整垫片 (10) 以便获得正确的轴向间隙量。 拆下螺栓 (8) 。 将工具 (R) 涂覆到螺栓 (8) 的螺纹上。 安装螺栓 (8) 。 拧紧螺栓 (8) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。
Show/hide table
图 13 | g01101563 |
- 冷却轴承 (5) 。 安装轴承 (5) 。 冷却轴承外圈 (7) 。 安装轴承外圈 (7) 。
Show/hide table
图 14 | g01101569 |
- 润滑唇形密封件 (6) 的唇部。 使用工具 (L) 安装唇形密封件 (6) 。
Show/hide table
图 15 | g01089845 |
- 安装原有的垫片 (4) 。 安装保持架 (3) 。 安装新螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。 使用工具 (K) 检查轴向间隙。 轴向间隙应为 0.15 ± 0.05 mm (0.006 ± 0.002 in)。 调整垫片 (4) 以便获得正确的轴向间隙量。 拆下螺栓 (1) 。 将工具 (R) 涂覆到螺栓 (1) 的螺纹上。 安装螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。
Show/hide table
图 16 | g01101571 |
- 安装工具 (M) 。
Show/hide table
图 17 | g01101572 |
- 安装挡圈 (22) 。 安装新螺栓 (21) 。 拧紧螺栓 (21) 至扭矩为 270 ± 40 N·m 199 ± 30 lb (ft)。
Show/hide table
图 18 | g01103085 |
- 安装衬套 (16) 和螺栓 (15) 。 拧紧螺栓 (15) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。
Show/hide table
图 19 | g01101644 |
- 拆下四颗螺栓 (12) 。
Show/hide table
图 20 | g01101583 |
- 安装支架 (14) 。 将工具 (R) 涂覆到新螺栓 (12) 上。 安装新螺栓 (12) 。 拧紧螺栓 (12) 至扭矩为 270 ± 40 N·m (199 ± 30 lb ft)。
Show/hide table
图 21 | g01102670 |
- 冷却轴组件 (47) 。 安装齿圈 (49) 。 安装把颗螺栓 (48) 。
Show/hide table
图 22 | g01102674 |
- 如图所示,将伞齿轮和分动器齿轮 (2) 放置到位。 将工具 (H) 和适当的起吊设备连接到轴组件 (47) 上。 轴组件 (47) 的重量约为 113 kg (250 lb)。 安装轴组件 (47) 。 拆下工具 (H) 。
Show/hide table
图 23 | g01090067 |
- 安装新螺母 (46) 和螺栓。 使用工具 (N) 拧紧螺母 (46) 。 将螺母 (46) 拧紧至扭矩为 1125 ± 100 N·m (830 ± 74 lb ft)。
Show/hide table
图 24 | g01090066 |
- 加热轴承 (45) 。 安装轴承 (45) 。 使用工具 (E) 安装挡圈 (44) 。
Show/hide table
图 25 | g01101594 |
- 冷却轴承外圈 (43) 。 安装轴承座圈 (43) 。 安装挡圈 (42) 。
Show/hide table
图 26 | g01090060 |
- 将工具 (B) 和适当的起吊设备连接到保持架 (41) 上。 安装工具 (A) 。 保持架 (41) 的重量约为 45 kg (100 lb)。 安装保持架 (41) 。
Show/hide table
图 27 | g01102675 |
- 拆下工具 (A) ,然后降下保持架 (41) 。
Show/hide table
图 28 | g01089994 |
- 将工具 (P) 涂覆到螺栓 (40) 的螺纹上。 将螺栓 (40) 安装到伞齿轮和分动器齿轮 (2) 中。 拧紧螺栓 (40) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。
Show/hide table
图 29 | g01089993 |
- 重新将伞齿轮和分动器齿轮壳体 (2) 放置到位,以便使轴组件 (47) 处于垂直位置。 安装轴承内圈 (39) 。
Show/hide table
图 30 | g01101603 |
- 冷却轴承外圈 (38) 。 安装轴承外圈 (38) 。
Show/hide table
图 31 | g01089988 |
- 冷却轴承外圈 (37) 。 安装轴承外圈 (37) 。
Show/hide table
图 32 | g01089985 |
- 安装原有的垫片组 (36) 和保持架 (35) 。
Show/hide table
图 33 | g01101605 |
- 安装间隔套 (33) 。
Show/hide table
图 34 | g01101606 |
- 安装轴承内圈 (32) 。
Show/hide table
图 35 | g01101607 |
- 安装垫圈 (31) 。 将工具 (Q) 涂覆到轴组件 (47) 的螺纹上。
Show/hide table
图 36 | g01101608 |
- 安装锁紧垫圈 (30) 和扳手螺母 (29) 。
Show/hide table
图 37 | g01101628 |
- 使用工具 (B) 、工具 (D) 和工具 (J) ,以便拧紧扳手螺母 (29) 。 拧紧扳手螺母 (29) 至扭矩为 2375 ± 70 N·m (1752 ± 52 lb ft)。
Show/hide table
图 38 | g01101629 |
- 把锁紧垫圈 (30) 上的锁舌弯到扳手螺母 (29) 的狭槽中。
Show/hide table
图 39 | g01101632 |
- 安装螺栓 (34) 。 拧紧螺栓 (34) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。
Show/hide table
图 40 | g01101634 |
- 使用工具 (K) 检查齿隙。 在三个位置检查齿隙。 在三个位置中测得的齿隙不得有任何超过 0.15 mm (0.006 in) 的变动量。
Show/hide table
图 41 | g01101637 |
- 该齿隙应为 0.36 ± 0.12 mm (0.014 ± 0.005 in)。
- 调整垫片 (36) 以便获得正确的齿隙。 获得正确的齿隙后,拆下螺栓 (34) 。 将工具 (P) 涂覆到螺栓 (34) 的螺纹上。 安装螺栓 (34) 。 拧紧螺栓 (34) 至扭矩为 135 ± 20 N·m (100 ± 15 lb ft)。
Show/hide table
图 42 | g01101642 |
- 拆下工具 (M) 。
End By: 连接变速箱和伞齿轮。 请参考 拆解和组装, "变速箱和伞齿轮 - 连接"。
Caterpillar Information System:
980H Wheel Loader Machine Systems Hydraulic Tank - Install
390F MHPU Mobile Hydraulic Power Unit Circuit Breakers - Reset
Machine Security System General Information
D10T Track-Type Tractor Power Train Transmission and Bevel Gears - Install
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Temperature Sensor (Torque Converter Oil)
930H Wheel Loader Steering System Solenoid Valve (Quick Steer)
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Relief Valve (Torque Converter Outlet)
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Torque Converter
637G Wheel Tractor-Scraper Wheel Tractor Power Train Torque Converter, Transmission and Transfer Gear - Connect
637G Wheel Tractor-Scraper Wheel Tractor Power Train Torque Converter, Transmission and Transfer Gear - Separate
D11T Track-Type Tractor Window Wipers - Inspect/Replace
980H Wheel Loader Machine Systems Hydraulic Tank - Remove
Machine Security System Normal Operation
826H Landfill Compactor, 825H Soil Compactor and 824H Wheel Dozer Engine and Transmission Support Group
Machine Security System System Components
980H Wheel Loader Machine Systems Counterweight - Remove and Install
Machine Security System Electrical Component and Connector Locations
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
980H Wheel Loader Power Train Engine and Transmission Support Group
980H Wheel Loader Machine Systems Hydraulic Tank - Disassemble
C11 and C13 Engines Engine Oil Filter Base
980H Wheel Loader Power Train Torque Converter (Freewheel Stator)
525C, 535C and 545C Wheel Skidders Secondary Steering - If Equipped
525C, 535C and 545C Wheel Skidders Parking Brake