Steering Motor - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-1861     | 挡圈钳     | 1     |
B     | 8T-0266     | 螺栓     | 1     |
C     | 5P-4808     | 十字挡块     | 2     |
5F-7369 | 滑板     | 2     | |
3H-0465 | 带螺纹的接头     | 4     | |
1B-4207 | 腿     | 2     | |
4K-0367 | 全高螺母     | 1     | |
1U-9895 | 十字挡块     | 1     | |
5/8 X 11 X 16 杆     | 1     | ||
D     | 1P-1860     | 挡圈钳     | 1     |
E     | 8H-0663     | 轴承拉拔器     | 1     |
F     | 6V-2012     | 深度千分尺     | 1     |
G     | 9S-3263     | 螺纹锁固胶     | 1     |
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 使用适当的压具安装轴承 (25) 和轴承 (26) 。
Show/hide table
图 1 | g00991485 |
- 使用工具 (D) 安装挡圈 (24) 。
Show/hide table
图 2 | g00900318 |
- 将密封件 (12) 安装到盖 (11) 中。 将垫片 (14) 、盖 (11) 和挡圈 (10) 安装到旋转祖件 (14A) 上。
Show/hide table
图 3 | g00991476 |
- 使用游标卡尺测量轴承组件。 尺寸 (X) 为 111.3 ± 0.100 mm (4.382 ± 0.004 in). 该测量确定旋转总成的正确角度。
Show/hide table
图 4 | g01880488 |
- 如有必要,增加或减少垫片 (14) 。
- 获得正确的尺寸后,从旋转组件 (14A) 上拆下挡圈 (10) 、盖 (11) 和垫片 (14) 。
- 安装盘 (22) 和中心销 (23) 。
Show/hide table
图 5 | g00900319 |
- 安装新的活塞环 (21) 。 将活塞环加热到 80 °C (176 °F)。 冷却活塞 (20) 。
注: 活塞环已经做上标记。 从活塞端部必须可以看到标记。
Show/hide table
图 6 | g00900321 |
- 将活塞 (20) 安装到固定板 (19) 中。
Show/hide table
图 7 | g00900323 |
- 将螺钉 (18) 安装到固定板 (19) 中。
Show/hide table
图 8 | g00900324 |
注: 如果在螺钉上预涂了螺纹锁固胶,则必须用新螺钉更换螺钉 (18) 。
- 将弹簧 (16) 安装到油缸筒 (15) 中。 请勿安装垫片 (17) 。
Show/hide table
图 9 | g00901525 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将油缸筒 (15) 安装到活塞上。
Show/hide table
图 10 | g01073537 |
- 安装油缸筒 (15) 。 安装工具 (B) ,以便固定油缸筒 (15) 。
Show/hide table
图 11 | g00900326 |
- 将旋转总成 (14A) 安装到壳体中。
Show/hide table
图 12 | g00903330 |
注: 将壳体加热到 80 °C (176 °F)。 冷却旋转总成。
- 拆下工具 (B) 。
Show/hide table
图 13 | g00706486 |
- 安装垫片 (14) 。
Show/hide table
图 14 | g00900330 |
- 安装 O 形密封圈 (13) 。
Show/hide table
图 15 | g00900331 |
- 安装盖 (11) 。
Show/hide table
图 16 | g00901350 |
- 使用工具 (A) 以便安装挡圈 (10) 。
- 安装中心销 (9) 。
Show/hide table
图 17 | g00900336 |
- 安装弹簧座 (8) 。
- 从阀总成 (4) 上安装弹簧 (7) 。
Show/hide table
图 18 | g00900337 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 将销 (6) 安装到阀总成 (4) 中。
Show/hide table
图 19 | g00900338 |
- 将盘 (5) 安装到阀总成 (4) 中。
Show/hide table
图 20 | g00903326 |
- 将阀总成 (4) 安装到原有位置中。
Show/hide table
图 21 | g00900341 |
- 使用工具 (E) 向下推动板和油缸筒。 使用工具 (F) 测量 0.325 ± 0.075 mm (0.013 ± 0.003 in) 的深度。 记录距离测量值并参阅技术规格, RENR7532-04, "转向马达"了解正确的垫片。
Show/hide table
图 22 | g00901523 |
- 拆下阀总成 (4) 。
Show/hide table
图 23 | g00900341 |
- 安装工具 (B) 。
Show/hide table
图 24 | g00706486 |
- 使用工具 (A) 以拆下挡圈 (10) 。
Show/hide table
图 25 | g00901350 |
- 拆下盖 (11) 。
Show/hide table
图 26 | g00900333 |
- 拆下 O 形密封圈 (13) 。
Show/hide table
图 27 | g00900331 |
- 拆下垫片 (14) 。
Show/hide table
图 28 | g00900330 |
- 安装工具 (C) 。
Show/hide table
图 29 | g00900329 |
Show/hide table
图 30 | g00903330 |
- 从壳体上拆下旋转总成 (14A) 。
- 拆下工具 (B) 。
Show/hide table
图 31 | g00900326 |
- 拆下油缸筒 (15) 。
- 从油缸筒 (15) 上拆下弹簧 (16) 。
Show/hide table
图 32 | g00901525 |
- 安装弹簧 (16) ,然后修正油缸筒 (15) 中的垫片厚度 (17) 。
Show/hide table
图 33 | g00900325 |
- 安装油缸筒 (15) 。 安装工具 (B) ,以便固定油缸筒 (15) 。
Show/hide table
图 34 | g00900326 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 将旋转总成 (14A) 安装到壳体中。
Show/hide table
图 35 | g00903330 |
注: 将壳体加热到 80 °C (176 °F)。 冷却旋转总成。
- 拆下工具 (B) 。
Show/hide table
图 36 | g00706486 |
- 安装垫片 (14) 。
Show/hide table
图 37 | g00900330 |
- 安装 O 形密封圈 (13) 。
Show/hide table
图 38 | g00900331 |
- 安装盖 (11) 。
Show/hide table
图 39 | g00901350 |
- 使用工具 (A) 以便安装挡圈 (10) 。
- 定位转速传感器 (9B) 。
Show/hide table
图 40 | g01069802 |
- 安装螺栓 (9A) 。
- 将阀总成 (4) 安装到原有位置中。
Show/hide table
图 41 | g00900341 |
- 安装 O 形密封圈 (3) 。
- 将马达头 (2) 安装到原有位置中。
Show/hide table
图 42 | g01069806 |
- 在螺栓 (1) 上使用工具 (G) 并安装螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 15.5 ± 1.5 N·m (137 ± 13 lb in)。
End By: 安装转向马达。 请参考 拆解和组装, "转向马达 - 安装"。
Caterpillar Information System:
D9T Track-Type Tractor Machine Systems Steering Motor - Disassemble
Product Link - PL102C Diagnostic Capabilities
988H Wheel Loader, 834H Wheel Dozer and 836H Landfill Compactor Machine Systems Governor Pedal
988H Wheel Loader Electrohydraulic System Bucket Control (Pins and Bearings)
994D Wheel Loader Air Dryer Desiccant - Replace
988H Wheel Loader Electrohydraulic System Position Sensor (Lift Linkage, Tilt Linkage)
Product Link - PL102C Configuration
994F Wheel Loader Fast Fill Service Center
988H Wheel Loader Electrohydraulic System Lift Cylinder
Bench Test Procedure for a 938H and 938G Series 2 Wheel Loader and IT38H and IT38G Series 2 Integrated Toolcarrier Transmission{3030, 3073} Bench Test Procedure for a 938H and 938G Series 2 Wheel Loader and IT38H and IT38G Series 2 Integrated Toolcarrier Transmission{3030, 3073}
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0626 - FMI 04
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0626 - FMI 03
3126B Engine for Caterpillar Built Machines Connecting Rod
994F Wheel Loader Machine Systems Radiator Cap
988H Wheel Loader Electrohydraulic System Main Control Valve
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0628 - FMI 03
994F Wheel Loader Engine Water Pump - Inspect
854G Wheel Dozer Hydraulic System Oil Coolers and Cooling System Operation
2004/05/24 An Improved Plug is Now Used in the Manifold for the Pressure Reducing Valve {3206, 5117}
Product Link - PL102C Electronic Service Tool Does Not Communicate with ECM
C27 and C32 Engines for Caterpillar Built Machines Fuel Filter Base
Electrical System for All Caterpillar Products Basic Circuit Theory
Electrical System for All Caterpillar Products Ohms Law
Electrical System for All Caterpillar Products Electrical Measurement