Pilot Valve - Assemble
组装步骤
- 安装 O 形密封圈 (55) 和 (56) 。 安装备用环 (57) 。 将柱塞 (59) 和弹簧 (58) 安装到真空膜盒 (54) 中。 对其他三个真空膜盒重复该步骤。
Show/hide table
图 1 | g01061091 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将真空膜盒 (54) 安装到阀 (33) 中。
Show/hide table
图 2 | g00475958 |
- 安装接头 (53) 。
Show/hide table
图 3 | g00475956 |
- 将 O 形密封圈 (52) 安装到真空膜盒 (50) 上。
Show/hide table
图 4 | g00475954 |
- 将真空膜盒 (50) 安装到阀 (33) 中。
Show/hide table
图 5 | g00475952 |
- 将 O 形密封圈 (51) 安装到柱塞 (48) 上。
Show/hide table
图 6 | g01061737 |
- 将三个柱塞组件 (48) 安装到阀 (33) 中。
Show/hide table
图 7 | g01061090 |
- 将垫圈 (45) 、隔套 (46) 、真空膜盒 (47) 和两个密封垫 (49) 分别安装到三个柱塞组件上。
Show/hide table
图 8 | g01061076 |
- 将适配器 (41) 、密封垫 (42) 和弹簧 (43) 安装到磁管 (44) 中。 将套筒 (40) 安装到每个磁管 (44) 中。
Show/hide table
图 9 | g01061075 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 对准线束组件 (39) 和阀 (33) 上的标记。 将磁管安装到初始位置。
Show/hide table
图 10 | g00475917 |
- 将枢轴接头 (37) 和螺栓 (38) 安装到板 (1) 上。
Show/hide table
图 11 | g00475916 |
- 将磁管和阀 (33) 安装到板 (1) 上。
Show/hide table
图 12 | g01061074 |
Show/hide table
图 13 | g01061061 |
- 安装卡箍板 (35) 。 拧紧螺栓 (34) 前,检查导线位置以避免损坏。 安装螺栓 (34) 。
- 安装柱塞 (36) 。
- 将螺母 (31) 和枢轴盘 (32) 安装到阀 (33) 上。
Show/hide table
图 14 | g01061060 |
- 安装 O 形密封圈 (28) 和 (29) 。 将备用环 (30) 安装到真空膜盒 (27) 上。
Show/hide table
图 15 | g00475664 |
- 将接头 (26) 安装到每个真空膜盒 (27) 上。
Show/hide table
图 16 | g01061059 |
- 将柱塞 (22) 、隔套 (23) 和密封件 (24) 安装到真空膜盒 (19) 中。 将 O 形密封圈 (25) 安装到真空膜盒 (19) 上。
Show/hide table
图 17 | g01061058 |
- 将弹簧 (20) 安装到柱塞 (21) 上。
Show/hide table
图 18 | g01061416 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装柱塞 (21) ,然后将真空膜盒 (11) 安装到阀中。
- 安装两个密封垫 (19) 、垫圈 (13) 、隔套 (12) 和弹簧 (14) 。 安装阀体 (15) 、适配器 (16) 、密封垫 (17) 和套筒 (18) 。 对每个真空膜盒 (11) 重复该步骤。
Show/hide table
图 19 | g01061415 |
Show/hide table
图 20 | g01061057 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将阀安置到板 (1) 上,然后安装螺栓 (10) 。
Show/hide table
图 21 | g00475594 |
- 安装支架 (8) 和螺栓 (7) 。
Show/hide table
图 22 | g01061056 |
- 安装四个柱塞 (9) 。
- 安装枢轴盘 (4) 和销 (6) 。 安装固定销 (6) 的挡圈 (5) 。
Show/hide table
图 23 | g01061055 |
- 将防护罩 (2) 和防护罩 (3) 安装到安装底盘 (1) 上。
Show/hide table
图 24 | g01061054 |
End By: 安装先导控制阀。 请参考 拆解和装配, "先导操作液压控制阀 - 安装"。
Caterpillar Information System:
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Pilot Valve - Disassemble
D11R Track-Type Tractor Cooling System Coolant Sample (Level 2) - Obtain
D11R Track-Type Tractor Cooling System Coolant Sample (Level 1) - Obtain
D11R Track-Type Tractor Cooling System Coolant Extender (ELC) - Add
D10R Track-Type Tractor Bulldozer Tilt Brace
D10T Track-Type Tractor Power Train Transmission Hydraulic Control
Dimensions for the 994 Wheel Loader Hitch{7051, 7054, 7057, 7100} Dimensions for the 994 Wheel Loader Hitch{7051, 7054, 7057, 7100}
D11R Track-Type Tractor Operation Information
D10R Track-Type Tractor Engine Starting with Prelubrication System
988G Wheel Loader Power Train Torque Converter (Lockup) - Assemble
950G Series II Wheel Loader System Components
988G Wheel Loader Power Train Torque Converter (Lockup) - Disassemble
D11R Track-Type Tractor Indicators and Gauges - Test
966G II and 972G II Wheel Loaders Autoshift Control
D10R Track-Type Tractor Cooling System Coolant (ELC) - Change
992G Wheel Loader Ether Starting Aid Cylinder - Replace - If Equipped
D10R Track-Type Tractor Engine Valve Lash - Check/Adjust
994F Wheel Loader Fuses - Replace
950G Series II Wheel Loader Hydraulic Tank
2004/04/12 A Tolerance Has Been Added to the Positioning of Lubrication Holes on Lift Arm Pins {6107, 6118}
950G Series II Wheel Loader Hose and Coupling
950G Series II Wheel Loader Accumulator
992G Wheel Loader Electrohydraulic System Position Sensor (Lift Linkage) - Calibrate
992G Wheel Loader Electrohydraulic System Position Sensor (Tilt Linkage) - Calibrate