Engine Oil Level - Check
Show/hide table
| NOTICE |
|---|
|
Do not under fill or overfill engine crankcase with oil. Either condition can cause engine damage. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Open the engine access door on the right rear side of the machine. The engine oil dipstick is located on the right side of the engine near the engine oil filter.
- Remove engine oil dipstick (2) and wipe the dipstick with a clean cloth. Then, insert the dipstick and remove the dipstick again. This will ensure a more accurate measurement of the engine oil level.
- While the engine is stopped, check the "ENGINE STOPPED" side of engine oil dipstick (2). Maintain the oil level between the marks on the dipstick.
- If necessary, remove oil filler plug (1) and add oil through the oil filler tube.
- Clean the oil filler plug and install the oil filler plug.
- Close the engine access door.
Show/hide table
| |
| Illustration 1 | g00791374 |
Caterpillar Information System:
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems MID 079 - CID 1706 - FMI 03
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems MID 079 - CID 1705 - FMI 06
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System Electronic Control Module (Autoshift)
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems MID 079 - CID 1705 - FMI 05
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Engine Oil (High Speed) and Oil Filter - Change - If Equipped
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems MID 079 - CID 1705 - FMI 03
621G and 627G Wheel Tractor-Scrapers Machine Systems Hydraulic Tank - Remove
3054 Engine Automatic Timing Advance Unit - Test
Product Identification Numbers (PIN) Location Guide Trencher
3054 Engine Fuel Injection Nozzle - Test
Product Identification Numbers (PIN) Location Guide Vibratory Compactor (Work Tool)
Product Identification Numbers (PIN) Location Guide Power Module
3054 Engine Engine Valve Lash - Inspect/Adjust
3054 Engine Valve Depth - Inspect
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems MID 079 - CID 1706 - FMI 05
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Engine Oil and Filter - Change
3054 Engine Valve Guide - Inspect
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems MID 079 - CID 1706 - FMI 06
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems MID 079 - CID 1707 - FMI 03
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System Sensors
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System Solenoid Valves
Instructions for Installation of Turbine Precleaners on Products with Dust Ejectors {1055} Instructions for Installation of Turbine Precleaners on Products with Dust Ejectors {1055}
3054 Engine Cooling System - Inspect
3176C and 3406E Engines for Caterpillar Built Machines System Configuration Parameters