Service Mode
Show/hide table
图 1 | g01155283 |
以下维修程序和功能通过控制器可用:
- 控制器通知监控系统关于机器的情况。 列举一些例子:液压油温度, 发动机冷却液温度 和 燃油油位。
- 控制器通知监控系统关于电子控制系统的任何现有的和/或过去的故障。
- 对控制器进行各种设定。
- 对电子控制系统进行调节和测试。
Show/hide table
图 2 | g01152977 |
监视器键盘 (8) 向上键 (9) 向右键 (10) 归位键 (11) 主菜单键 (12) 向左键 (13) 向下键 (14) 取消键或返回键 (15) 确定键 |
键盘的按键用于进入维修模式。 按键用于更改模式。 按相应的键,直到消息中心显示所需的模式。 通过以下步骤进入维修模式:
- 从 "MAIN MENU(主菜单)"将显示上面的屏幕。 按向右键 (9) 或向左键 (12) ,直到 "SERVICE(维修)" 突出显示。
Show/hide table
图 4 g01128879 - "SERVICE(维修)"突出显示后,按"确定"键 (15)。
Show/hide table
图 5 g01128858 - 按"确定"键 (15) 后,将显示上面的屏幕。 方向键用于输入密码。 密码 "FFF2" 可用于访问进行维修时使用的所有菜单。 有关密码输入的更多信息,请参阅本手册的系统运作, "密码输入"章节。
Show/hide table
图 6 g01153285 - 输入正确的密码后,会显示图 6。 这表示已进入维修模式。 以下选项可用,并将在本手册中详细介绍:
- 保养
- 密码更改
- DIAGNOSTIC(诊断)
- ECM INFO(ECM 信息)
- STATUS(状态)
- CALIBRATIONS(标定)
- DEVICE TEST(设备测试)
- OVERRIDE(超弛)
- CONFIGURATIONS(配置)
- TOOL PROGRAM(机具编制)
Show/hide table
图 3 | g01128832 |
有两种方法可以终止维修模式。 第一种方法是将钥匙起动开关转到 OFF(关闭)位置。 维修模式将在起动开关转到 OFF(断开)位置 10 秒后终止。 如果您不想关闭机器,请使用如下所示的程序:
第二种方法是通过按归位键 (10)。 按归位键 (10) 后,监视器将停止维修模式内的功能。 归位键 (10) 在每个菜单内均可用。
注: 如果在功能处理期间按下归位键 (10),监视器可能需要 1 到 2 秒钟才能返回到默认屏幕。
Caterpillar Information System:
C7 and C9 Marine Engines Sensors and Electrical Connectors
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head - Install - C32
C9 Generator Set Engines Fuel Filter Base
2005/03/07 New Factory Password System for Caterpillar Engines {1000, 1900}
C9 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
UPS View User Guide Communication Connections
UPS View User Guide General Information (Getting Started)
UPS View User Guide Log On
UPS View User Guide Font Setting
UPS View User Guide Display Configuration
C3.3 and C4.4 Generator Sets Engine Oil and Filter - Change
UPS View User Guide Tile Arrangement
3406E, C12, C15 and C18 Marine Engines Can Not Reach Top Engine RPM
D Series Excavator Monitoring System Password Change Mode
C3.3 and C4.4 Generator Sets Fuel Injection Nozzles - Test/Exchange
3176C and 3196 Industrial Engines Air Compressor Drive Gear - Install - Two Cylinder
UPS View User Guide Log Files
C9 Engines for Caterpillar Built Machines Unit Injector - Remove
C9 Engines for Caterpillar Built Machines Unit Injector - Install
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
UPS View User Guide Remote Notification
C7 and C9 Marine Engines Analog Sensor Supply Circuit - Test
2005/03/07 Improved Alternator Adjusting Rod {1405}
UPS View User Guide User Operations