Electric Starting Motor
Show/hide table
图 1 | g03366944 |
Show/hide table
352-9765 电起动马达总成 和 150-8867 电起动马达总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
1     | 2     | 6V-8188 螺母     | 最终安装扭矩为 30.5 ± 3.5 N·m (269.9 ± 30.9 lb in)。     |
B     | -     | -     | 小齿轮和壳体之间的间隙为 9.1 mm (0.36 in)。     |
2     | 1     | 4B-2049 螺母     | 最终安装扭矩为 3.4 ± 1.2 N·m (30.1 ± 10.6 lb in)。     |
3     | 1     | 4B-2049 螺母     | 开关接线端。 开关端子必须用热收缩管绝缘。 不要使用模压端子。 最终安装扭矩为 3.4 ± 1.2 N·m (30.1 ± 10.6 lb in)。     |
4     | 1     | 6V-8188 螺母     | 接地终端。 最终安装扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。     |
5     | 1     | 6V-8188 螺母     | 蓄电池终端。 蓄电池端子螺母最多可使用三条电缆或导线端子。 两个电缆接线端可以等于或高于 0 AWG。 拧紧至扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。     |
6     | -     | -     | 马达机架终端。 拧紧至扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。     |
-     | -     | -     | 10 V 和 20° C (68° F) 时的吸合电流为 82.0 至 94.2 安培。     |
10 V 和 20° C (68° F) 时的保持电流最大为 16.4 安培。 |
|||
-     | -     | -     | 当从小齿轮端观看电起动马达时,马达顺时针旋转。     |
-     | -     | -     | 25 °C (77 °F) 时无负载:     |
转速为 4600 至 7100 rpm。 | |||
电流为 210 至 305 安培。 | |||
电压为 11 VDC。 |
Caterpillar Information System:
Machine Security System Electrical Component and Connector Locations
Machine Security System System Components
Machine Security System Normal Operation
390F MHPU Mobile Hydraulic Power Unit Circuit Breakers - Reset
Machine Security System General Information
793B Off-Highway Truck Suspension Cylinder General Information
C15 and C18 Petroleum Generator Sets Electronic Modular Control Panel 3 (EMCP 3)
Marine Multi-Station Control System Parameter - Program
Marine Multi-Station Control System Data Link (Engine Monitoring System and Engine Vision) - Test
Marine Multi-Station Control System PCP CID 1822 - FMI 09
Marine Multi-Station Control System PCP CID 1816 - FMI 09
3126B and 3126E On-highway Engines Pistons and Connecting Rods - Install
C9 On-highway Engine Air Inlet Elbow
C9 On-highway Engine Air Inlet Heater
C9 On-highway Engine Air Inlet Heater
C9 On-highway Engine Air Inlet Heater
TH31-E61 and TH35-E81 Petroleum Transmissions Torque Converter and Transmission Oil Sample - Obtain
C9 Industrial Engines Camshaft
C11 and C13 Engines Engine Oil Filter Base
EMCP3 Diagnostic Capabilities
C15 and C18 Industrial Engines Cylinder Head - Remove
C15 and C18 Industrial Engines Cylinder Head - Install
C9 On-highway Engine Engine Oil Pan
EMCP3 Service Tools