Camshaft
Show/hide table
Illustration 1 | g00988290 |
(1) End play of a new camshaft ... 0.10 ± 0.25 mm (0.0039 ± 0.0098 inch)
Maximum permissible end play of a worn camshaft ... 0.30 mm (0.0118 inch)
(2) Tighten the thrust plate bolts to the following torque. ... 10 to 13 N·m (7 to 10 lb ft)
(3) The diameters of the camshaft journals are given in the following table.
Show/hide table
Diameters of Camshaft Journals     | ||
Camshaft Journals     | Standard Diameter     | Service Limit     |
No. 1,2     | 53.94 to 53.96 mm (2.123 to 2.124 inch)     |
53.90 mm (2.122 inch)     |
No. 3     | 52.94 to 52.96 mm (2.084 to 2.085 inch)     |
52.90 mm (2.083 inch)     |
Show/hide table
Illustration 2 | g00987844 |
(A) Camshaft lobe lift
-
Naturally aspirated engines
- Inlet lobe ... 6.722 mm (0.2646 inch)
- Exhaust lobe ... 6.720 mm (0.2645 inch)
-
Turbocharged engines
- Inlet lobe ... 6.682 mm (0.2631 inch)
- Exhaust lobe ... 6.722 mm (0.2646 inch)
The service limit for camshaft lobe lift is given below:
-
Naturally aspirated engines
- Inlet lobe ... 6.222 mm (0.2450 inch)
- Exhaust lobe ... 6.220 mm (0.2449 inch)
-
Turbocharged engines
- Inlet lobe ... 6.182 mm (0.2434 inch)
- Exhaust lobe ... 6.222 mm (0.2450 inch)
(B) Camshaft lobe height
(C) Base circle
To determine the lobe lift, use the procedure that follows:
- Measure the camshaft lobe height (B) .
- Measure the base circle (C) .
- Subtract the base circle that is found in Step 2 from the camshaft lobe height that is found in Step 1. The difference is the camshaft lobe lift.
If the camshaft lobe lift is less than the service limit, replace the camshaft.
Show/hide table
Illustration 3 | g01014070 |
(4) Camshaft
Deflection over the full length of the camshaft
- Maximum at assembly ... 0.02 mm (0.0008 inch)
- Repair limit ... 0.05 mm (0.0020 inch)
Caterpillar Information System:
G3516B Engines MID 036 - CID 0017 - FMI 05 Fuel Shutoff Valve open circuit
G3500B Engines Thermocouple
G3516B Engines MID 036 - CID 1720 - FMI 06 Turbo Compressor Bypass Valve Solenoid shrt to gnd
G3516B Engines MID 036 - CID 1720 - FMI 05 Turbo Compressor Bypass Valve Solenoid open
3054E Industrial Engine Housing (Front) - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Exhaust Manifold
G3500B Engines Thermocouple
G3516B Engines Compressor Bypass
Cold Weather Recommendations for On-Highway Diesel Truck Engines Engine Oil
3406E, C-10 and C-12 On-highway Engines Factory Passwords
3054C Industrial Engine Housing (Front) - Install
3408E and 3412E Engines for Caterpillar Built Machines Vibration Damper - Check
G3500B Engines Engine Mount
Installation Guide for the C1.5 Marine Generator Set and the C2.2 Marine Generator Set{1000, 1404, 7274} Installation Guide for the C1.5 Marine Generator Set and the C2.2 Marine Generator Set{1000, 1404, 7274}
2004/06/01 Checking the Timing Marks on the Front Gear Train {1204, 1212, 1234}
3046 Engine for Caterpillar Built Machines Engine Oil Relief Valve
3046 Engine for Caterpillar Built Machines Engine Oil Pump
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Pressure
G3500B Engines Engine Oil Lines - Turbocharger Oil Lines
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Pan
3046 Engine for Caterpillar Built Machines Water Temperature Regulator
3044C Industrial Engine and Engines for Caterpillar Built Machines Cylinder Block
C4.4 Industrial Engine Engine Oil Pump - Inspect
G3520C and G3520E Generator Set Engines Rocker Shaft - Disassemble