Engine Oil Cooler - Install
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁发动机机油冷却器壳体与缸体的配合面。
- 将发动机机油冷却器 (2) 和新的密封件 (5) 定位在发动机机油冷却器壳体上。 安装调整螺钉 (7) ,将发动机机油冷却器固定到壳体上。
Show/hide table
图 1 | g00952614 |
- 将发动机机油冷却器壳体 (3) 和新的密封垫 (1) 定位到缸体上。 安装调整螺钉 (4) 和调整螺钉 (6) ,将发动机机油冷却器壳体固定到缸体上。
注: 切勿在密封垫 (1) 上涂抹密封胶。
- 将所有调整螺钉 (4、6 和 7) 拧紧到正确的扭矩。 有关更多信息,请参阅扭矩技术参数手册, "公制紧固件标准扭矩"。
- 向冷却系统加注冷却液。 向润滑系统中加注发动机油。
注: 有关发动机的冷却系统容量和润滑系统容量,请参阅操作和保养手册, "加注容量"。
Caterpillar Information System:
3054E Industrial Engine Engine Oil Cooler - Remove
3054E Industrial Engine Engine Oil Filter Base - Remove and Install
C11 and C13 On-Highway Engines Belt Tensioner
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Service Brake Pedal Position (Switch 1) Circuit - Test
C1.5 and C2.2 Generator Sets Voltage Regulators
2003/02/03 Special Instruction, REHS1238, "Obtaining Factory Passwords and Software Enabled Attachments" is Available {7610}
3054E Industrial Engine Fuel Priming Pump and Fuel Filter Base - Remove and Install
3054E Industrial Engine Piston Cooling Jets - Remove and Install
320B, 320B L and 320B N Excavators Swing Drive Oil Sample - Obtain
C13 and C15 Engines for Combat and Tactical Vehicles Remote PTO Accelerator Position Sensor Circuit - Test
3054E Industrial Engine Crankshaft Front Seal - Install
3054E Industrial Engine Crankshaft Front Seal - Remove
C13, C15, and C18 Tier 4 Final Engines Water Pump
3054E Industrial Engine Water Pump - Remove and Install
Supplement to the Operation and Maintenance Manual{0707} Supplement to the Operation and Maintenance Manual{0707}
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Tachometer Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Two Speed Axle Switch Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Vehicle Speed and Speedometer Circuit - Test
C11, C13 and C15 On-highway Engines System Overview
C18 Generator set and C18 Marine Engines Auxiliary Water Pump - Disassemble - Type 1
C18 Generator set and C18 Marine Engines Auxiliary Water Pump - Assemble - Type 1
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Increased Engine Oil Temperature - Inspect
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Cooling System - Check - Overheating
C13 Engines for Caterpillar Built Machines Compression Brake