Factory Default Values of Configuration Parameters
The default factory settings that follow are for the control module that has the Check SYNC option.
Miscellaneous Settings
Show/hide table
| Generator Poles | 4 |
| Engine Speed Sensor Fitted | No |
| AC System | 3 phase, 4 wire |
| Enable Generator Sequence Alarm | Yes |
| Enable bus sequence alarm | Yes |
| Phase Sequence | L1, L2, L3 |
| Display indications on display | No |
| Display load switching state machine | No |
| Enable fast loading feature | Yes |
| Are warnings are latched | No |
| Start key must be held down to crank | No |
| Audible alarm prior to starting | No |
| Number of start attempts | 3 |
Input Settings
Show/hide table
| Low Oil Pressure Input Type | VDO 10 bar |
| High cooling temperature input type | VDO 120 °C (248 °F) |
Alarm/Shutdown Settings
Show/hide table
| Alarm/Shutdown | Trip | Return |
|---|---|---|
| Low oil pressure prealarm | 1.17 Bar, 117 kPa (17 psi) |
1.24 Bar, i 124 kPa (18 psi) |
| Low oil pressure shutdown | 1.03 Bar, 14.9 Psi 103 kPa (14.9 psi) |
- |
| High coolant temp prealarm | 115 °C (239 °F) |
110 °C (230 °F) |
| High coolant temp shutdown | 120 °C (248 °F) |
- |
Digital Inputs
Show/hide table
| 1 | Remote start close to activate |
| 2 | Generator closed auxiliary close to activate |
| 3 | User configured close to activate warning active from safety on |
| 4 | User configured close to activate shutdown always active |
| 5 | User configured close to activate shutdown active from safety on |
| 6 | User configured close to activate electrtical trip always active |
| 7 | User configured close to activate electrical trip active from safety on |
| 8 | User configured close to activate indication always active |
| 9 | Panel lock close to activate |
Indicator Settings
Show/hide table
 | |
| Illustration 1 | g00867288 |
Indicator Identification Diagram | |
Show/hide table
| 1 | On, Remote start present |
| 2 | On, Panel locked by digital input |
| 3 | On, Delayed alarms armed |
| 4 | On, Check sync |
Output Settings
Show/hide table
| Module Relays | |
|---|---|
| 1 | Energize preheat (during preheat timer) |
| 2 | Energize Common alarm |
| 3 | Energize close generator |
| 4 | Energize system in auto mode |
| 5 | Energize close generator |
| 6 | Energize close generator request |
Show/hide table
| Expansion A | |
|---|---|
| 1 | Energize Output Not Used |
| 2 | Energize Output Not Used |
| 3 | Energize Output Not Used |
| 4 | Energize Output Not Used |
| 5 | Energize Output Not Used |
| 6 | Energize Output Not Used |
| 7 | Energize Output Not Used |
| 8 | Energize Output Not Used |
Show/hide table
| Expansion B | |
|---|---|
| 1 | Energize Output Not Used |
| 2 | Energize Output Not Used |
| 3 | Energize Output Not Used |
| 4 | Energize Output Not Used |
| 5 | Energize Output Not Used |
| 6 | Energize Output Not Used |
| 7 | Energize Output Not Used |
| 8 | Energize Output Not Used |
Timer Settings
Show/hide table
| Starting Timers | |
|---|---|
| Start Delay | 5 Seconds |
| Preheat | 0 Seconds |
| Preheat Bypass | 0 Minutes |
| Sensor fail delay | 2 Seconds |
| Cranking Time | 10 Seconds |
| Crank Rest Time | 10 Seconds |
| Smoke Limit | 0 Seconds |
| Smoke Limit Off | 0 Seconds |
| Safety On Delay | 10 Seconds |
| Overspeed Overshoot | 0 Seconds |
Show/hide table
| Load Timers | |
|---|---|
| Warming Up Time | 0 Seconds |
| Transfer Time | 0.7 Seconds |
| Breaker Close Pulse | 0.0 Seconds |
| Breaker Trip Pulse | 0.0 Seconds |
| Generator Close Timer | 1.3 Seconds |
| Generator Open Timer | 5 Seconds |
Show/hide table
| Stopping Timers | |
|---|---|
| Return Delay | 30 Seconds |
| Cooling Time | 30 Seconds |
| ETS Solenoid Hold | 0 Seconds |
| Fail to Stop Delay | 30 Seconds |
Show/hide table
| Other Timers | |
|---|---|
| Battery low volts delay | 1 minute |
| Battery high volts delay | 1 minute |
| Display auto scroll timer | 2 seconds |
| Display page timer | 5 minutes |
| Reverse power alarm | 0.0 seconds |
Generator Settings
Show/hide table
| Voltage And Frequency Settings | Trip | Return |
|---|---|---|
| Under volts trip | 184 VAC | - |
| Under volts pre alarm | 196 VAC | 207 VAC |
| Over volts prealarm | 265 VAC | 253 VAC |
| Over volts trip | 276 VAC | - |
| Under frequency trip | 40.0 Hz | - |
| Under frequency prealarm | 42.0 Hz | 45.0 Hz |
| Over frequency prealarm | 55.0 Hz | 52.0 Hz |
| Over frequency trip | 57.0 Hz | - |
Show/hide table
| Power Settings | |
|---|---|
| Generator CT primary | 500 A |
| Generator full load rating | 500 A |
| Earth fault CT primary rating | 500 A |
| Trip Curve/Multiplier Action | - |
| Delayed overdurrent | 100% (500 A) 36 Electrical trip |
| Short circuit | 300% (1500 A) 6 Electrical trip |
| Earth fault | 10% (50 A) 1000 Shutdown |
| Reverse power | 0.3 KW Electrical trip |
Show/hide table
| Synchronizing (check sync) Settings | |
|---|---|
| Enable synchronising | Yes |
| Check sync phase angle | 10° |
| Check sync frequency | 0.2 Hz |
| Check sync RMS voltage | 5.0 VAC |
| Sync advance time | 0 mS |
| Sync hold time | 100 mS |
| Fail to sync time | 30.0 seconds |
Engine Settings
Show/hide table
| Crank Disconnect Trip | |
| Crank disconnect on generator frequency | 21.0 Hz |
| Crank disconnect on generator voltage | Disabled |
| Crank disconnect on alternator | Disabled |
| Crank disconnect on oil pressure | Disabled |
| Check oil pressure prior to starting | Yes |
Show/hide table
| Speed Settings | |
|---|---|
| Overspeed Overshoot | 0% |
Show/hide table
| Plant Battery Settings | Trip | Return |
|---|---|---|
| Under volts warning | 8.0 VDC | 9.0 VDC |
| Over volts warning | 33.0 VDC | 32.0 VDC |
| Alternator warning | 8.0 VDC | - |
Show/hide table
| Maintenance Alarm Settings | |
|---|---|
| Enable maintenance alarm | No |
Show/hide table
| Exercise Scheduler Settings | |
|---|---|
| Enable exercise scheduler | No |
Show/hide table
| Language Settings | |
|---|---|
| Default language | English (UK) |
| User defined language 1 | Chinese (PRC) |
| User defined language 2 | Not Used |
| User defined language 3 | Not Used |
| User defined language 4 | Not Used |
Output Settings
Show/hide table
| Module Relays | |
|---|---|
| 1 | Energize preheat (during preheat timer) |
| 2 | Energize Common alarm |
| 3 | Energize close generator |
| 4 | Energize system in auto mode |
| 5 | Energize close generator |
| 6 | Energize close generator request |
Show/hide table
| Expansion A | |
|---|---|
| 1 | Energize Output Not Used |
| 2 | Energize Output Not Used |
| 3 | Energize Output Not Used |
| 4 | Energize Output Not Used |
| 5 | Energize Output Not Used |
| 6 | Energize Output Not Used |
| 7 | Energize Output Not Used |
| 8 | Energize Output Not Used |
Show/hide table
| Expansion B | |
|---|---|
| 1 | Energize Output Not Used |
| 2 | Energize Output Not Used |
| 3 | Energize Output Not Used |
| 4 | Energize Output Not Used |
| 5 | Energize Output Not Used |
| 6 | Energize Output Not Used |
| 7 | Energize Output Not Used |
| 8 | Energize Output Not Used |
Timer Settings
Show/hide table
| Starting Timers | |
|---|---|
| Start Delay | 5 Seconds |
| Preheat | 0 Seconds |
| Preheat Bypass | 0 Minutes |
| Sensor fail delay | 2 Seconds |
| Cranking Time | 10 Seconds |
| Crank Rest Time | 10 Seconds |
| Smoke Limit | 0 Seconds |
| Smoke Limit Off | 0 Seconds |
| Safety On Delay | 10 Seconds |
| Overspeed Overshoot | 0 Seconds |
Show/hide table
| Load Timers | |
|---|---|
| Warming Up Time | 0 Seconds |
| Transfer Time | 0.7 Seconds |
| Breaker Close Pulse | 0.0 Seconds |
| Breaker Trip Pulse | 0.0 Seconds |
| Generator Close Timer | 1.3 Seconds |
| Generator Open Timer | 5 Seconds |
Show/hide table
| Stopping Timers | |
|---|---|
| Return Delay | 30 Seconds |
| Cooling Time | 30 Seconds |
| ETS Solenoid Hold | 0 Seconds |
| Fail to Stop Delay | 30 Seconds |
Show/hide table
| Other Timers | |
|---|---|
| Battery low volts delay | 1 minute |
| Battery high volts delay | 1 minute |
| Display auto scroll timer | 2 seconds |
| Display page timer | 5 minutes |
| Reverse power alarm | 0.0 seconds |
Generator Settings
Show/hide table
| Voltage And Frequency Settings | Trip | Return |
|---|---|---|
| Under volts trip | 184 VAC | - |
| Under volts pre alarm | 196 VAC | 207 VAC |
| Over volts prealarm | 265 VAC | 253 VAC |
| Over volts trip | 276 VAC | - |
| Under frequency trip | 40.0 Hz | - |
| Under frequency prealarm | 42.0 Hz | 45.0 Hz |
| Over frequency prealarm | 55.0 Hz | 52.0 Hz |
| Over frequency trip | 57.0 Hz | - |
Show/hide table
| Power Settings | |
|---|---|
| Generator CT primary | 500 A |
| Generator full load rating | 500 A |
| Earth fault CT primary rating | 500 A |
| Trip Curve/Multiplier Action | - |
| Delayed overdurrent | 100% (500 A) 36 Electrical trip |
| Short circuit | 300% (1500 A) 6 Electrical trip |
| Earth fault | 10% (50 A) 1000 Shutdown |
| Reverse power | 0.3 KW Electrical trip |
Show/hide table
| Synchronizing (check sync) Settings | |
|---|---|
| Enable synchronising | Yes |
| Check sync phase angle | 10° |
| Check sync frequency | 0.2 Hz |
| Check sync RMS voltage | 5.0 VAC |
| Sync advance time | 0 mS |
| Sync hold time | 100 mS |
| Fail to sync time | 30.0 seconds |
Engine Settings
Show/hide table
| Crank Disconnect Trip | |
| Crank disconnect on generator frequency | 21.0 Hz |
| Crank disconnect on generator voltage | Disabled |
| Crank disconnect on alternator | Disabled |
| Crank disconnect on oil pressure | Disabled |
| Check oil pressure prior to starting | Yes |
Show/hide table
| Speed Settings | |
|---|---|
| Overspeed Overshoot | 0% |
Show/hide table
| Plant Battery Settings | Trip | Return |
|---|---|---|
| Under volts warning | 8.0 VDC | 9.0 VDC |
| Over volts warning | 33.0 VDC | 32.0 VDC |
| Alternator warning | 8.0 VDC | - |
Show/hide table
| Maintenance Alarm Settings | |
|---|---|
| Enable maintenance alarm | No |
Show/hide table
| Exercise Scheduler Settings | |
|---|---|
| Enable exercise scheduler | No |
Show/hide table
| Language Settings | |
|---|---|
| Default language | English (UK) |
| User defined language 1 | Chinese (PRC) |
| User defined language 2 | Not Used |
| User defined language 3 | Not Used |
| User defined language 4 | Not Used |
Caterpillar Information System:
C-15 and C-16 Industrial Engines General Information
PM820, PM822, and PM825 Cold Planer Track Drive Planetary Oil Sample - Obtain
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 S·O·S Oil Analysis
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Front Idler - Disassemble
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
G3500 Engines Overhaul (Major)
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Track - Connect
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Track - Separate
C12 Marine Engines Diagnostic Flash Code Retrieval
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Track Roller - Install
G3500 Engines Ignition System Spark Plugs - Inspect/Replace
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Track Roller - Assemble
3408E and 3412E Industrial Engines Flywheel Housing
797 Off-Highway Truck Braking System Relief Valve (Brake Oil Cooler) - Primary and Secondary
Electronic Modular Control Panel II (EMCP II) Electronic Control Module (Engine)
CPT372 Truck Mounted Pumper Reference Material
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Front Idler - Assemble
Electronic Modular Control Panel II (EMCP II) GSC CID 0110 - FMI 02 (for EUI Engines)
3408E and 3412E Industrial Engines Flywheel and Flywheel Housing Runout
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Recoil Spring - Disassemble
SR4 Generator with VR3 or VR4 Voltage Regulator Bearing - Remove and Install
SR4 Generator with VR3 or VR4 Voltage Regulator Exciter - Remove and Install
SR4 Generator with VR3 or VR4 Voltage Regulator Generator - Remove
SR4 Generator with VR3 or VR4 Voltage Regulator Generator - Install